background image

Chapter 1: 

Introduction

12

www.xilinx.com

ZC702 and ZVIK Getting Started Guide

UG926 (v3.0.1) February 12, 2013

°

SD  MMC Boot mode

°

Quad SPI flash memory

°

USB JTAG configuration port (Digilent module)

°

Platform cable header JTAG configuration port

For more detailed information about ZC702 board features, peripheral devices, and 

pinouts, see the hardware user guide 

UG850

ZC702 Evaluation Board for the Zynq-7000 

XC7Z020 All Programmable SoC User Guide

.

Key Features of the ZVIK

Key features of the additional components of the Zynq-7000 AP SoC Video and Imaging kit 

include:

• HDMI  input/output  FMC  module 

°

HDMI input 

°

HDMI output 

°

Video clock synthesizer 

°

Interface for ON Semiconductor VITA image sensor module

• ON Semiconductor VITA 2000 color image sensor module

°

Supports up to WXGA resolution: 1920 (H) x 1200 (V) format 

°

92 frames per second (fps) at full resolution

°

4.8 

μ

m x 4.8 

μ

m pixel size 

2

/

3

-inch optical format

°

Pipelined and triggered global shutter, rolling shutter 

°

Random programmable region of interest (ROI) readout

°

Automatic exposure control (AEC) 

• Standard interchangeable 

2

/

3

-inch, 8 mm C-mount lens

Summary of Contents for ZC702





















































Reviews: