manualshive.com logo in svg

Xilinx Virtex-5 FPGA ML561, User Manual

The Xilinx Virtex-5 FPGA ML561 offers outstanding performance and versatility for advanced electronic designs. For convenient usage, a comprehensive User Manual is available for free download at manualshive.com. This manual provides detailed instructions and valuable insights, ensuring seamless integration and successful implementation of this cutting-edge product.

Share
Download
background image

190

www.xilinx.com

Virtex-5 FPGA User Guide

UG190 (v5.0) June 19, 2009

Chapter 5:

Configurable Logic Blocks (CLBs)

Distributed RAM Data Flow

Synchronous Write Operation

The synchronous write operation is a single clock-edge operation with an active-High 
write-enable (WE) feature. When WE is High, the input (D) is loaded into the memory 
location at address A.

Asynchronous Read Operation

The output is determined by the address A (for single-port mode output/SPO output of 
dual-port mode), or address DPRA (DPO output of dual-port mode). Each time a new 
address is applied to the address pins, the data value in the memory location of that 
address is available on the output after the time delay to access the LUT. This operation is 
asynchronous and independent of the clock signal.

Distributed RAM Summary

•

Single-port and dual-port modes are available in SLICEMs.

•

A write operation requires one clock edge.

•

Read operations are asynchronous (Q output).

•

The data input has a setup-to-clock timing specification.

Read Only Memory (ROM)

Each function generator in SLICEMs and SLICELs can implement a 64 x 1-bit ROM. Three 
configurations are available: ROM64x1, ROM128x1, and ROM256x1. ROM contents are 
loaded at each device configuration. 

Table 5-6

 shows the number of LUTs occupied by each 

ROM configuration.

Shift Registers (Available in SLICEM only)

A SLICEM function generator can also be configured as a 32-bit shift register without using 
the flip-flops available in a slice. Used in this way, each LUT can delay serial data 
anywhere from one to 32 clock cycles. The shiftin D (DI1 LUT pin) and shiftout Q31 (MC31 
LUT pin) lines cascade LUTs to form larger shift registers. The four LUTs in a SLICEM are 
thus cascaded to produce delays up to 128 clock cycles. It is also possible to combine shift 
registers across more than one SLICEM. Note that there are no direct connections between 
slices to form longer shift registers, nor is the MC31 output at LUT B/C/D available. The 
resulting programmable delays can be used to balance the timing of data pipelines.

Applications requiring delay or latency compensation use these shift registers to develop 
efficient designs. Shift registers are also useful in synchronous FIFO and content 
addressable memory (CAM) designs. 

The write operation is synchronous with a clock input (CLK) and an optional clock enable 
(CE). A dynamic read access is performed through the 5-bit address bus, A[4:0]. The LSB of 
the LUT is unused and the software automatically ties it to a logic High. The configurable 
shift registers cannot be set or reset. The read is asynchronous; however, a storage element 

Table 5-6:

ROM Configuration

ROM

Number of LUTs

64 x 1

1

128 x 1

2

256 x 1

4

Summary of Contents for Virtex-5 FPGA ML561


































































































































































































































































































































































































Reviews:

No comments

Related manuals for Virtex-5 FPGA ML561

Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
Accuphase AD-60 Instruction Manual preview
AD-60
Brand: Accuphase Pages: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Brand: ADTRAN Pages: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Brand: Acrosser Technology Pages: 4
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
Delta Tau PMAC2-PC/104 Installation Manual preview
PMAC2-PC/104
Brand: Delta Tau Pages: 74
SIIG FireWire 800 + Hi-Speed USB Combo Quick Installation Manual preview
FireWire 800 + Hi-Speed USB Combo
Brand: SIIG Pages: 20
D3 DesignCore RVP-TDA3 Series Quick Start Manual preview
DesignCore RVP-TDA3 Series
Brand: D3 Pages: 34
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
Rane HAL1x System Installation Manual preview
HAL1x
Brand: Rane Pages: 128
Acard AEC-6885 User Manual preview
AEC-6885
Brand: Acard Pages: 34
Shure DFR22 Software Manual preview
DFR22
Brand: Shure Pages: 113
ENERMAX LIQMAX III ELC-LMT120-ARGB User Manual preview
LIQMAX III ELC-LMT120-ARGB
Brand: ENERMAX Pages: 32
Unex EVK-351 Quick Start Manual preview
EVK-351
Brand: Unex Pages: 27
IEI Technology Mustang-M2AE-MX1 User Manual preview
Mustang-M2AE-MX1
Brand: IEI Technology Pages: 58
Renesas R0E0144TNPFK00 User Manual preview
R0E0144TNPFK00
Brand: Renesas Pages: 4
Intellinet 720564 Instructions preview
720564
Brand: Intellinet Pages: 2

Brands by name

Popular brands

Load more brands