manualshive.com logo in svg

Xilica Audio Design Mini S4K1, User Manual, Page: 19 / 29

Share
Download
Xilica Audio Design Mini S4K1 User Manual Download Page 19

19

Step-by-Step Firmware Upgrade Guide

The hardware device must be connected and operational (Green indicator) before upgrading the firmware.

1. 

Download the latest firmware version for your device from our website. (

www.xilica.com

) 

In Network View, all the units on the network are displayed. The network connection indicator is displayed at 
the top left of each device.

2. 

Save any design files from the device onto your computer. All programmed data on the device will 

 

be erased during the upgrade process. (To save, navigate to the File tab at the top left of the software 

 

and click ‘Save’.)

 

After the firmware upgrade is complete, you may reload saved design files back into the device.

3. 

Right click the device that you would like to update. Select ‘Firmware Upgrade’.

4. 

A pop up window will ask you if you’d like to proceed with the firmware upgrade. Select “OK” to 

 proceed. 

NeuPanel: Firmware upgrade

Summary of Contents for Mini S4K1






























Reviews:

No comments