background image

Unpacking and Installation, TWTA Octagon CPU

MNC-0300-003

1 of 22

Revision N

Unpacking and Installation, TWTA Octagon CPU

Record of Changes

Revision ECO

Description

Date

Initiated By

A

9295

Original Release

11/29/2001 A.L. Crozier, Jr.

B

9933

Add information for Tri-band Power 
Connector

06/21/2002 A.L. Crozier, Jr.

C

10096 Replace Fig. 7

07/14/2002 A.L. Crozier, Jr.

D

10197 Update RF Inhibit Information

08/26/2002 A.L. Crozier, Jr.

E

10490 Update to reflect waveguide flange 

protection

12/10/2002 A.L. Crozier, Jr.

F

10980 Update Figure 5 to show proper pinouts 04/22/2003 A.L. Crozier, Jr.

G

11340 Add Waveguide Torque Table 08/13/2003 A.L. 

Crozier, 

Jr.

H

11883 Correct pinouts on MS Power Plug. Add 

Waveguide Switch connector pinouts.

03/08/2004 A.L. Crozier, Jr.

J

12470 Add Hardware Address Select and 

Discrete HV ON Indicator

09/01/2004 A.L. Crozier, Jr.

K

12715 Change to reflect absorptive vice 

reflective filtering for W/G

04/21/2005 J. Thompson

L

12775 Change title, add Octagon TWT note 

and various other edits

04/26/2005 T. Stewart

M

12927 Add German Language translation to 

comply with CE requirement

07/07/2005 A. L. Crozier, Jr.

N

13332 Auxiliary Connector Figure

08/22/2005 A. Auld

Summary of Contents for TWTA























Reviews: