manualshive.com logo in svg

Xerox LS 3270, User Manual

Share
Download
Xerox LS 3270 User Manual Download Page 19

Programming the Xerox LS 3270
Xerox LS 3270

- 19 -

Y74

Printer Symbol Set Definition Strings

Y75

Overwrite Translate Table

Y77

Reset APL Translate Table

Y78

Select APL Translate Table

Y79

ida 820 AFP Font Offset

Y80

Overwrite APL Translate Table

Y88

Margin Definition

Y89

Enable Margin Definition

Y90

Define User Escape String

Y91

Font Definiti on

Y92

Font Point Size Definition Strings

Y93

Font Attribute Definition

Y94

Font Typeface Definition

Y96

Font Change Simulation

Y98

Automatic Page Orientation

Y100

Port Sharing Option

Y110

idaAFP Orientation Support

Y111

idaAFP Duplex Support

Y112

idaAFP PCL5 Font Support

Y113

idaAFP Early Print Complete

Y114

idaAFP Colour Support

Y115

idaAFP Miscellaneous

Y119

Autoconfiguration Select

Y120

Print Test Page at power on

ESC Features:

%%

Special transparent feature (Multiple paired Hex 
transparent).

e.g.: %%

1B45%

where  %  is the defined ESC character.

%

Special transparent feature (Single paired Hex 
transparent).

where  %  is the defined ESC character

.

Send Logo:

L

Send logo (Logo is defined in Y63).

Get other manuals https://www.bkmanuals.com

Summary of Contents for LS 3270
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands