background image

Technical Resource Center:

Toll Free:

800 394.9900

Website:

www.futuregraphicsllc.com

Brand names and trademarks are the
properties of their respective holders
and are for descriptive use only.

Step 1

Place the cartridge on the workbench so
the handle is up and the fill plug is facing
you.

(See Photo 1)

Using diagonal cutters remove the 
cartridge pin that holds the two sections
of the cartridge together.

(See Photo 2)

Step 2

Rotate the cartridge 180°. Remove the
cartridge pin from the gear side of the
cartridge.

(See Photo 3)

Step 3

Grab the waste hopper by the handle
and lift the hopper off of the toner
hopper.

(See Photo 4)

Photo 1

Photo 2

Photo 3

N24/3240TECH

Photo 4

Compaq LN32/LNM40
Xerox Docuprint N24/32/40
Xerox DocuCentre 220/230/332/340
IBM InfoPrint 32/40
QMS 3260/4032
Dataproducts
Genicom Microlaser 320/320N

108473-B2, 113R173
113R120, 13R273
113R274, 90H3566
1710307-001, 113R00173
5A6530P01

Diagonal Cutters
Needle Nose Pliers 
Philips Screwdriver
Small Flat Blade Screwdriver

Technical Instructions

Printers

Supplies

Tools

1

CORPORATE 

LOS ANGELES

T 800 394.9900   

818 837.8100

F 800 394.9910   

818 838.7047

DALLAS

T 877 499.4989

972 840.4989

F 877 774.1750

972 840.1750

ATLANTA

T 877 676.4223

770 516.9488

F 877 337.7976

770 516.7794

MIAMI

T 800 595.4297

305 594.3396

F 800 522.8640

305 594.3309

SANFORD

T 800 786.9041

919 775.4551

F 800 786.9049

919 775.4584

TORONTO

T 877 848.0818

905 712.9501

F 877 772.6773

905 712.9502

NEW YORK

T 800 431.7884

631 345.0121

F 800 431.8812

631 345.0690

SYDNEY

T 02 9648.2630
F 02 9648.2635

BUENOS AIRES

T 0810.444.2656

011 4583.5900

F 011.4584.3100

MELBOURNE

T 1 800 003 100
F 1 800 004 302

Summary of Contents for DocuPrint N24











Reviews: