background image

NOTE

 

 

 

NOTE 2:

Touch Screen device driver must be installed onto your computer in order for the
Touch Screen to become functional. Xenarc Technologies uses Resistive Touch

Screen panels in the 700TSU monitor. Touch Screen drivers and software for different 

 operating systems can be found in the included CD-ROM disc. You can refer to this

manual for a walkthrough of Touch Screen Driver installation under Microsoft Windows XP.

NOTE 3:

The maximum voltage supported by the monitor is 35V DC. Feeding the monitor
with higher voltage will damage the monitor and void the warranty. Please use a
fused power source if you decide to wire the monitor directly to your car’s electrical
system. It is also crucial that you check the polarity of the connection.

NOTE 4:

If the monitor is not displaying the VGA signal properly, the VGA signal might be out
of range. Please try changing your display refresh rate to 60, 70, 72, or 75Hertz.

NOTE 5:

Please note that the LCD screen is made with high-precision technology. However,
black points or bright points of light (red, blue, or green) may appear constantly on
the LCD screen, and irregular colored stripes or brightness may appear on the LCD
screen. This is not malfunction. (Effective dots: more than 99.999%)

 

The length of the mouting screw.
(common between right side and left side)

For Technical Support, please contact us at: 

Xenarc Technologies Corp.
Toll Free: 888-656-6536
E-mail: [email protected]
Website: www.xenarc.com

|

Additional Info

22

NOTE 1:

If you are trying to connect the monitor to a laptop computer, please make sure to 
enable external monitor setting on your laptop. Some laptop computers have four 
modes: Laptop Display Only, Duplicate display Mode, Extend Display Mode, and 
Projector Only Mode. Please select the mode you wish to use.

Summary of Contents for 700TSU
























Reviews: