background image

 

DO NOT RETURN TO RETAILER WHERE PURCHASED. 

CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or [email protected] 

 

IMPORTANT INSTRUCTIONS AND WARNINGS 

 

 

WARNING 

READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT 

 

AGE & WEIGHT LIMIT 

 

This product is designed to be used by up to seven (7) children between the ages of 3 to 8.    Maximum user 

weight is 100 pounds (45 kg) each with a combined maximum weight of 700 pounds (318 kgs). 

 

The play  set  is  designed for  children  over  three  (3)  years  of age up  to  (8)  years  of  age.    Use  by  smaller 

children can result in entrapment. 

 

On-site adult supervision is required at all times for children of all ages.     

 

Do not allow use by children with any physical condition that may affect his/her ability to use this equipment 

safely. 

 

BEFORE YOU BEGIN 

 

Carefully read all instructions in this manual before assembling and using this product.     

 

The unit must be assembled by adults

. Heavy duty working gloves must be worn to avoid injuries during 

assembly.   

 

Children must not use the equipment until it is properly assembled and anchored.     

 

Adult supervision is required during the use of this equipment at all times.

 

 

Unpack all parts. Take a complete inventory of all parts and hardware using the parts and hardware lists in 

the following pages. If any parts are missing, do not return to the store. Please call customer service toll-free 

number listed on the cover page for assistance. Store the product back in the original box and do not begin to 

install until all parts are obtained.     

 

LOCATION OF PLAY SET 

 

The  equipment  must  be  placed  more  than  six  (6)  feet  (1.8  meters)  from  any  structures  or  obstructions, 

including  but  not  limited  to  buildings,  fence,  garage,  trees,  laundry  lines,  electrical  wires.  Children  can  be 

seriously injured running or swinging into obstacles.     

 

The  play  set  must  be  installed  on  level  ground

.    Uneven  ground  must  be  leveled  prior  to  installation.   

Installation on sloping or uneven ground will put stress on the joints, causing the unit to become loose and 

unstable which may result in serious injuries. 

 

Remove  any  tripping  hazards  from  the  safe  play  area,  such  as  roots,  tree  stumps,  rocks,  landscaping, 

sprinkler heads, railroad ties, plumbing and electrical connections. 

 

Windy conditions: it is possible for the product to be blown about by a high wind. if you anticipate 

high winds, the frame should be secured to the ground with the use of an Anchor kit. If you anticipate 

severe  winds,  the  product  should  be  moved  to  a  sheltered  location  or  completely  disassembled. 

Anchor kits can be ordered directly from XDP RECREATION at https//:www.xdp-recreation.com or by 

calling 1-866-884-0535.

Summary of Contents for 86150
































Reviews: