background image

 

DO NOT RETURN TO RETAILER WHERE PURCHASED. 

CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or [email protected] 

 

                                        86150/86155 

         

Freedom Swing

Camo Commander

 

 

 

 

 

 

 

 

 

 

 

 

 

Assembled dimensions are 192” x 106” x 76”    Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully 

assembled.   

OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S 

GUIDE 

   

WARNING! 

Please  read  this  entire  instruction  and  assembly  manual  completely  before  proceeding. 

You  must  follow  all  safety 

instructions while using this equipment.    The surface area where this swing set is set up must be level and free of all debris. This 

set  is  designed  to  be  anchored  into  the  ground  and  is  not  to  be  set  up  on  any  hard  surfaces  such  as  concrete,  hardened  soil,  or 

asphalt.    Proper  surfacing  under  and  surrounding  the  set  adds  to  the  safety  level  such  as  sand  or  mulch.  Read  all  cautionary 

statements  on  the  following  pages  before  using  this  equipment  and  save  this  instruction  manual.   

DO  NOT  ALLOW 

CHILDREN TO PLAY ON THIS GYM SET UNSUPERVISED!

   

CONSTANT ADULT SUPERVISION IS REQUIRED

.   

Do not use  when raining or during any inclement  weather (i.e. rain, sleet, snow, ice, high  winds, thunderstorms, or lightening).   

DO NOT ALLOW CHILDREN TO JUMP ON OR CLIMB UP ON THIS SET'S TOP BAR. 

For warranty details and registration see the back page of this manual. 

 

FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL 

 
 
 
 
 
 
 

Please retain sales receipt for warranty purposes. 

  DO NOT RETURN THE 

SET  TO  THE  STORE

. If replacement parts or customer service is needed please contact XDP Recreation by 

email at [email protected] or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), 

Monday - Friday.    This gym is designed to be used safely by up to seven (7) children, ages 3 years to 8 years, with weight 

capacity  of  100  lbs  per  child  or    total  combined  weight  limit  of  700  lbs  for  all  seven  (7)  children.    This  play  gym  is 

designed for backyard use only and is NOT intended for playgrounds, schools, day care facilities, nurseries or other public 

places.   

Follow all assembly instructions carefully and as directed in this manual

.    This gym conforms to all safety 

requirements  by  ASTM  for  Home  Playground  equipment  when  properly  assembled  using  the  instructions  enclosed.   

Adult assembly is required.    Contains small parts. 

For proper stability and safety this gym set should be installed with 

ground anchors. 

IF NEEDED, GROUND ANCHORS CAN BE BOUGHT FROM THE STORE YOU PURCHASED THIS SET AT 

OR BY PURCHASING FROM XDP RECREATION'S WEBSITE AT www.xdp-recreation.com 

 

XDP RECREATION LLC, 5910 SHILOH ROAD EAST, UNIT 108, ALPHARETTA, GEORGIA 30005 

Summary of Contents for 86150
































Reviews: