background image

 

DO NOT RETURN TO RETAILER WHERE YOU PURCHASED AT. 

CONTACT XDP FOR PARTS AND SUPPORT AT 1.866.884.0535 or [email protected] 

 

DO NOT install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick floor. 

A  fall  onto  a  hard  surface  can  result  in  serious  injury  or  death  to  the  user

.  The following  is  a  list  of 

recommended ground covers from the Consumer Product Safety Commission: 

SUGGESTED MATERIAL   

 

 

 

UNCOMPRESSED DEPTH 

Double Shredded Bark Mulch   

 

 

9” 

Uniform Wood Chips   

 

 

 

 

12” 

Fine Gravel   

 

 

 

 

 

 

12” 

Fine Sand 

 

 

 

 

 

 

 

12” 

 

The Consumer Product Safety Commission

’s Outdoor Home Playground Safety Handbook recommends to 

install  and  maintain  the  playground  equipment  over  at  least  9  inches  of  wood  chips,  mulch  or  shredded 

rubber (for equipment up to 8 feet high) or sand or pea gravel (for equipment no more than 5 feet high) as 

shock absorbing material.    Dirt and grass, which are the most prevalent surfaces under home playground 

equipment, do not adequately protect children from serious head injuries. Install protective surfacing at least 

six feet in all directions from play equipment. For swings, the surface should extend, in back and front, twice 

the height of the suspending bar. You should consult a local contractor about ways to secure the product in 

your location. Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick 
floor.  Please  refer  to  the  CONSUMER  PRODUCT  SAFETY  COMMISSION’S  OUTDOOR  HOME 
PLAYGROUND SAFETY HANDBOOK for detailed guidelines to prevent injuries from falls and other hazards 

on public and home playgrounds.     

 

WARNINGS ON ANCHORING 

This product must be anchored into the ground to prevent movement and to make the swing set more stable 
during use. 
 
Some consumers want an anchoring system that allows the product to be moved to different locations. Other 
consumers want to keep their swing set in a permanent location.   
 
It is highly recommended that you seek the opinion from a local licensed contractor on the best way to secure the 
swing set in your location. The best way to anchor a product is to create a concrete footing and use that as a 
base for an anchor. Whatever method you prefer for your location, an anchoring system for this product should be 
used at all times. 
 

WEATHER CONDITIONS 

 

DO NOT

 use this equipment if the swing seat, slide or any parts are wet. Use the play set only when the 

parts are clean and dry. If the equipment is wet, the user could slip and suffer injuries.       

 

Please be aware of weather conditions when using the equipment. If it is too windy, users could lose 

control and suffer injuries. The playground equipment must be properly anchored, stored away or 

restricted from use during inclement weather such as heavy winds or severe weather storms. You 

should consult a local contractor about ways to anchor the product in your location

.       

Summary of Contents for 74510G








































Reviews: