xDEEP Ghost User Manual Download Page 4

3 Safety rules 

 

 

 

1.

 

Before  every  dive,  carefully  inspect  all  elements  of  the  equipment,  including  the  BC.  For  further 
information on the subject, read: “Pre-dive inspection”. 

2.

 

Do  not  dive  with the BC if there are  signs of defective operation, damage or  wear, such a  BC should be 
withdrawn from use until it is repaired by an authorized WreckAndReef distributor. 

3.

 

During  diving,  perform  mutual  buddy-check,  visually  inspecting  the  BC  against  any  leakages  or  other 
irregularities. Arrange checkout procedures with your buddy and practice relevant diving signs once again 
before diving. 

4.

 

In case of an uncontrolled ascent, you should immediately start releasing air from the BC in order to stop 
or slow down the rate of ascent. 

5.

 

In  order  not  to  drown  as  a  result  of  an  uncontrolled  descent,  in  all  cases  you  should  be  able  to  use  an 
emergency source of buoyancy or remove the weight. The BC 

CANNOT

 be the only source of buoyancy! 

6.

 

Do not use your BC to lift or bring heavy objects to the surface. Doing so may result in a serious accident 
due  to  damage  done  to  the  BC  or  an  uncontrolled  ascent.  For  bringing  objects  heavier  than  2kg,  use 
appropriate equipment, such as a lift bag. 

7.

 

To prevent the BC from damage, avoid prolonged exposure of your BC to direct sunlight or extreme heat 
and keep it away from sharp objects. 

8.

 

Do not inhale air  from the BC. It may contain harmful contaminants, gases, or dangerous bacteria  which 
evolve in damp places. 

9.

 

A BC is not a lifejacket and does not guarantee a head-up position of the user on the surface. Therefore, 
you should always dive with a buddy in case of losing consciousness on the surface. 

10.

 

Do not lift or move the BC by pulling the inflator hose. Such practice may result in irreparable damage to 
the BC.  

11.

 

When diving in cold water (below 10 degrees Celsius), you should take into account that the inflator may 
freeze, as a result of which, it may supply air in an uncontrolled way, or other irregularities in its operation 
may appear. Before diving in cold water, it is necessary that you practice emergency procedures should the 
inflator freeze! 

 
 
 
 
 

xDEEP BCDs are designed to provide the user with safety and comfort. Improper use may result in an 

accident, therefore it is necessary to comply with ALL of the following rules. 

Danger! 

Summary of Contents for Ghost





















Reviews: