background image

4–1

4

Troubleshooting

Chapter 4

 will help you identify the source of most problems that can 

occur with the inverter.

If you have a problem with the inverter, please review this chapter before 
contacting place of purchase.

If you are unable to solve a problem and need to contact place of 
purchase, record the information in the form 

“Information About Your 

System” on page WA–5

Common Problems

Buzz in Audio Equipment

Some inexpensive stereo systems may emit a buzzing noise from their 
loudspeakers when operated from the inverter. This occurs because the 
power supply in the audio system does not adequately filter the modified 
sine wave produced by the inverter. The only solution is to use a sound 
system that has a higher quality power supply.

Television Reception

When the inverter is operating, it can interfere with television reception 
on some channels. If interference occurs, try the following:

1. Make sure that the chassis ground screw on the rear of the inverter is 

solidly connected to the ground system of your vehicle.

2. Make sure that the television antenna provides an adequate (“snow-

free”) signal, and that you are using good quality cable between the 
antenna and the television.

3. Keep the cables between the battery and the inverter as short as 

possible, and ensure that the positive and negative cables are run very 
close to each other. This minimizes radiated interference from the 
cables.

4. Move the television as far away from the inverter as possible.

5. Do not operate high power loads with the inverter while the television 

is on.

XPower_Inverter_5000_Owners_Guide.book  Page 1  Friday, April 4, 2008  2:59 PM

Summary of Contents for XPower 5000







































Reviews: