manualshive.com logo in svg

Xantrex Trace TM500A, Installation & Operation Manual

Share
Download
Xantrex Trace TM500A Installation & Operation Manual Download Page 17

11

© 2001 Xantrex Technology Inc.
P/N 973-0012-01-02 Rev. A 05/01

Connecting the Shunt Board

• Remove the fuse from the in-line fuse holder by rotating the fuse holder

cap counterclockwise.

• Connect the ring terminal from the fuse holder to the battery’s positive

terminal.

• Connect the shunt communications cable into the RJ11 jack on the shunt

board.  This cable can be extended up to 100 feet (30 meters).

• Replace the fuse in the fuse holder.  Replace the fuse holder cap by

pushing and rotating it clockwise.

INVERTER

-

SHUNT

DC FUSE

DISCONNECT

SHUNT IN-LINE FUSE

SHUNT WIRE

3507-00B-F01

J2

J1

INVERTER

RC4/RC8
REMOTE

JACK

GROUND WIRE

(IF RUN IS OVER

100 FEET)

SHUNT JACK

REMOTE JACK

INVERTER ON/OFF

REMOTE CABLE

TC10, TC25, TC50, TC100

(NOT SUPPLIED)

TRACE

METER

(Back View)

BATTERY

+

-

+

Figure 2-10

Circuit Diagram

Figure 2-9

In-line Fuse

In-line Fuse

To battery’s

positive

terminal

To J1

connector on

back of

meter

2.0  INSTALLATION

Summary of Contents for Trace TM500A













































Reviews:

No comments

Brands by name

Popular brands

Load more brands