background image

Xantrex Technology, Inc. 

Distributed Power Markets 

161G South Vasco Road 

Livermore, CA  94550 USA 

Phone +1 925.245.5400 

Fax +1 925.245.1022

 

 

XANTREX PV SERIES LIMITED WARRANTY AND REGISTRATION 

 
Xantrex Technology warrants all equipment supplied to Customer under this purchase 
order against defects in workmanship and material for a period of (12) twelve months 
from delivery, provided that the equipment has been operated and maintained in 
accordance with the service manual provided with the equipment.  Should Customer 
give Xantrex written notice of any such defects within the warranty period, and 
Xantrex’s inspection confirms the existence of such defects, Xantrex shall correct the 
defects, either by repair or replacement, at its sole option. 
 
For wall-mounted products (generally, below 30 kW in rating), defective products must 
be  returned  to  Xantrex  or  it  Authorized  Service  Center  in  the  original  or  equivalent 
packaging.  The cost of transportation and insurance on items returned for service is at 
the Customer’s expense.  Return transportation and insurance expense shall be borne by 
Xantrex. 
 
For floor mounted inverter products (generally, 30 kW in rating and above), warranty 
repairs or replacements are performed at the installation site.  Xantrex’s material, labor, 
freight and travel/living expenses associated with such repair or replacement shall be 
borne by Xantrex.   
 
In either case, Customer’s labor and travel/living expense shall be borne by Customer.  
Xantrex will assume no expense, liability or responsibility for repairs made by or for 
Customer without written authority from Xantrex.  Xantrex shall not be responsible for 
any consequential, incidental or similar damages. 
 
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 
 
Project Name   

______________________ 

Customer PO # 

______________________ 

Inverter Serial # 

______________________ 

Delivery Date   

______________________ 

 
 
Xantrex Authorized Signature: 

 

 

Customer Authorized Signature: 

 
________________________   ________________________ 
 
________________________   ________________________ 
Date   

 

 

 

 

          Date 

Summary of Contents for PV-100208















































Reviews: