background image

5

Amplifiers & Preamplifiers

6-26-00

Gain (@ max VC): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unity

Input Overload: . . . . . . . . . . . . . . . . . . 4.5 V RMS  (@ max VC)

Input Impedance: . . . . . . . . . . . . . . . . . > 40 k Ohms (ea. input)

Output Impedance: . . . . . . . . . . . . . . . . . . . . . . . . 470 Ohms (allows output to be
                                                                               paralleled for mono, if needed)

Volume Attenuation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . -80 dB

Signal to Noise: . . . . . . . . . . . . . . . . . . . . . . 100 dB (re 2V out)

THD: (VC -10 dB) . . . . . . . . . . . . . . . 0.01% at 2.0 V input level

Channel Separation: . . . . . . . . . . . . . . . . . . .  > 75 dB @ 1 kHz

Freq. Response:  . . . . . . . . . . . . . . . . . . . 20Hz-20kHz +/- 1 dB

Bass Range: . . . . . . . . . . . . . . . . . . . .+/- 12 dB  (in 2 dB steps)

Treble Range: . . . . . . . . . . . . . . . . . . +/- 12 dB  (in 2 dB steps)

Video IN/OUT Impedance: . . . . . . . . . . . . . . . . . . . . .75 Ohms.

Video Insertion Loss: . . . . . . . . . . . . . . 50 Hz - 10 mHz < 1 dB.

Video Out-IN Isolation: . . . . . . . . . . . . 50 Hz - 10 mHz > 55 dB.

A/V Inputs/Outputs: . . . . . . . . . . . . . . . . RCA type phono jacks

IR Code Group: . . . . . . . . . . . . . . . . . . . . . . 40  (factory preset)

Power Requirements: . . . . . . . . . . . . . . . .  15 VAC @ 300 mA.

Power and IR Inputs: . . . . . . . . . . . . . 4-terminal screw terminal

plug-in connector

Dimensions:  . . . . . . . . . . . . . . . . . . .10" W  x  3" D  x  1 3/8" H

254mm x 73mm x 35mm

RP41AV SPECIFICATIONS

(Power supply included)

RP41AV

Summary of Contents for RP41AV







Reviews: