background image

Model PA635X 

 

Page 11 

 

© 2001 Xantech Corporation 

SPECIFICATIONS 
 

Number of channels 

Power Output 

Rated continuous power, each channel, all six channels 
simultaneously driven, 20 Hz to 20kHz, at rated THD 

35 Watts at 8 Ohms 

Power Output 

Short term continuous, each channel, 2 channels driven,  
1 kHz, at rated THD 

55 Watts at 8 Ohms 
80 Watts at 4 Ohms 

Bridged Power Output 

Short term continuous, one pair driven at 1 kHz, at rated THD 

150 Watts at 8 Ohms 

Rated THD 

< 0.08% 

Damping Factor 

at 50 Hz, half rated power 

> 100 

S/N Ratio 

A-weighted, shorted inputs, ref to rated power 

> 100 dB 

Frequency Response 

at 1 Watt, ± 3dB 

12 Hz to 55 kHz 

Input Sensitivity 

at rated power, stereo mode, input gain (IR controlled setting) 

Max: 0.5 V 
Default: 1.0 V 
Minimum: Off 

Input Impedance 

Local Inputs:  22 kOhms 
Common Audio Buss Inputs: 70kOhms 

Power Source 

120 VAC, 60 Hz 
TMRA 30° Celsius.  If this temperature is exceeded, you will 
need to provide additional ventilation to ensure proper 
operation. 
 
240 VAC, 50 Hz (European version) 

Power Consumption 

No signal:  20 Watts 
6 Channels at 1/10 rated power: 150 Watts 
6 Channels at rated power: 600 Watts 
6 Channels Bridged at 660 Watts 

Remote On/Off

 and 

CI Voltage/Current 

+5 V to +30 VDC (16 mA at +12 VDC) 

Line Fuse Rating 

120V version: 6.25A Slow Blow 250 VAC 
240V version: 3.15A Time-Lag 250 VAC 

Dimensions 

17” W x 3.75” H x 15” D 
(429 mm W x 94

 

mm H x 379 mm D) 

Weight 

22.3 lbs (10.1 Kg) 

 

Summary of Contents for PA635X













Reviews: