background image

 

10

 

Left handle bar controls 

 

 

Headlight Switch 

High Beam – Push switch up 
Low Beam – Push switch down 

Horizontal Switch 

Left Turn Signal – Slide switch to the left 
Right Turn Signal – Slide switch to the right 
Turning off Signal – Press central release button 

Horn Button 

Sounds Horn – Push red button on the left. 

Rear Brake Lever 

When  Brake  Handle  is  compressed  the  rear  wheel 
will  slow  to  a  stop  and  power  will  be  cut  off.    Power 
will flow once lever has been released. 

 

 

Right handle bar controls 

 

Economy  Speed 
switch 

PLEASE READ 
CAREFULLY

 

To  prevent  the  speed  of  the  bike  from  exceeding 
30pmh,  set  the  switch  to  Low.   

NOTE  –  NEVER 

OPERATE  SWITCH  WHILE  RIDING

.    Rider  must 

come  to  a  complete  stop  before  switching  from  low  to 
high speed.  

INTERNAL DAMAGE can occur!

   

 

Front Brake Lever  When brake handle is compressed the front wheel will 

slow  to  a  stop  and  power  will  be  cut  off.    Power  will 
flow  once  lever  has  been  released.  To  start,  turn  the 
throttle counter clockwise. 

Throttle 

Turn throttle counter clockwise to increase speed. 

Parking Lights  

The  dashboard  lights,  headlight,  and  taillight  will  turn 
on when the switch is in the middle position.   

Head Light 

The  dashboard  lights,  headlight,  and  taillight  will  turn 
on when the switch is in the left position.   

 

 
 
 

 

 

Summary of Contents for XM-3100






















Reviews: