background image

Safety Precautions 

Warning! 

MOVING PARTS ENTANGLEMENT HAZARD 

Failure to observe these instructions could lead to severe injury or death. 

To avoid injury to hands or fingers 

Always keep hands clear of wire rope.hook loop,hook and fairlead opening during installation,operation, and when 

spooling in or out. 

Always use extreme caution when handling hook and wire rope during spooling operations. 

Always use supplied hook strap whenever spooling wire rope in or out,during installation or operation to avoid injury 

to hands or fingers. 

Warning 

CHEMICL AND FIRE HAZARD 

Failure to observe these instructions could lead to severe injury or death. 

Always remove jewelry and wear eye protection. 

Never lean over battery while making connections. 

Always verify area when drilling is clean of fuel line,fuel tank,brake lines,electrical wires,etc. 

Never route electrical cables: 

-Across any sharp edeges. 

-Through or near moving parts. 

-Near parts that become hot. 

Always insulate and protect all exposed wiring and electrical terminals. 

Always install termnial boots as directed in installation instructions. 

Warning   

FALLING OR CRUSHING HAZARD 

Failure to observe these instructions could lead to severe injury or death. 

Never use as an overhead hoist ,or to suspend a load. 

Never use to lift or move persons. 

 

CAUTION 

MOVING PARTS ENTANGLEMENT HAZARD 

Failure to observe these instructions could lead to minor or moderate injury. 

 

General Safety: 

Always know your winch: Take time to fully read and understand the included Installation and Operation guide,and 

Basic Guide to Winching Techniques, in order to understand your winch and winching operation. 

 

Never operate this winch if you are under 16 years of age. 

Never operate this winch when under the infulence of drugs, alcohol or medication. 

Never exceed winch or wire rope rated capacity. Double line using a snatch block to reduce winch load. 

 

Installation Safety: 

Always choose a mounting location that is sufficiently strong to withstand the maximum pulling capacity of your 

winch. 

Always use factory approved switches,remote controls,accessories and installation components. 

Summary of Contents for 20805002

















Reviews: