background image

- 8 -

- 9 -

Product Assembly

2 Mounting the Module with Camera

(1) Align the red positioning mount dot on the mount ring (at the real of module) with 

the red dot above the camera mount.(fig. 

1

 )

(2) Attach module to camera and turn 30 degrees clockwise, until  both bodies are 

completely stable union.(fig. 

2

 )

(3) Turn on the camera and module power. The image will appear on LCD screen 

indicate the handling is correct.         If the lens barrel can not extend properly, or 

error code shows on camera monitor, please refer to the troubleshooting section 

of this manual ; If unable to solve, please immediately contact your distributor for 

assistance, do not try to modify X-Loupe® product by yourself in any way.

UNLOCK

LOCK

Turn 30 degrees clockwise

Red Dot

1

2

(1) Get the lens and align the pogo pin -3 pin male header and 3 bolts on the rear 

of lens-  A , into the pogo pin female header and 3 notchs- B on lens mount of 

module (fig.  

1

  ), then attach the lens to module. 

(2) Rotate the lens spiral tooth clockwise until it is tight. But do not over-tighten!

(3) Open the battery cover on the button ( press C and to slide the battery cover in 

the direction indicated by the arrow,)  and fill in fully-charged Canon NB-4L Li-ion 

battery.(fig. 

2

 )

 Caution: 

NB-4L Li-ion battery charging 4 hrs for the first time; 1.5 hours for  

 

general usage.

(4) Turn on X-Loupe® module power. It will light up if handling is correct.

1 Mounting the lens on Module

Pogo pin (male) 

Power

Battery Insert 

Summary of Contents for Conceiver series MPG4 PLUS


















Reviews: