background image

U.L. 

AND F.C.C. CAUTIONS

FCC Caution: This equipment generates
and uses radio frequency energy, and if not
installed and used properly, that is, in strict

accordance with the manufacturer’s instruc-

tions, may cause interference to radio and

television reception. It has been type tested

and found to comply with the limits for re-

mote control security devices in accordance

with the specifications in subpart B of part

15 of FCC Rules, which are designed to

provide reasonable protection against such

interference in 

residential installation.

However, there is no guarantee that inter-
ference will not occur in particular instal-
lation. If this equipment does cause inter-
ference to radio or television reception,
which can be determined by unplugging the

equipment, the user is encouraged to try to

correct the interference by one or more of

the following measures.

Reorient antenna of the radio/TV

experiencing interference.

Relocate the Console with respect to

the radio/TV.

Move the Console away from the
radio/IV.

Plug the Console into an outlet on a

different branch circuit from the

radio/TV experiencing the interference.

If necessary, the user should consult the
dealer or manufacturer for additional sug-

gestions.

Important:
Your Security Console is FCC registered.
In order to fully comply with the FCC

rules, these instructions should be followed
prior to installing and using the product:

Connections cannot be made to coin-
operated telephones, or to party lines.

The KC requires that any umnections

to telephone lines are to use standard

plugs and adaptors.

Notify the telephone company that you
will be connecting a Registered unit to

the line. Give them the following infor-

mation regarding the Security Console:

A) FCC Registered Number

B4SUSA-65898-AL-T

B) Ringer Equivalence

3.

0.lB.

If a problem arises with your telephone
service after you have connected the
Security Console, disconnect the unit to
see if the problem is caused by its use.

If the Security Console is at fault, leave

it disconnected until it is repaired or re-

placed. If the telephone company
makes a service call to your home and
determines that the Security Console
has caused the problem, they have the

right to charge you for a service call.

Note: The suitability of this product to per-

form as a burglar alarm system or as an
emergency service device has not been

evaluated by Underwriters Laboratories

Inc.

Summary of Contents for POWERHOUSE DW534


































Reviews: