Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit repair,
component replacement or complete product replacement in the event of malfunction. The decision to repair or replace will
be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and excludes normal
wear and tear or cosmetic damage. Visit the product page located at
wyrestorm.com
for additional information on this
product including important technical information not provided in this document and warranty terms & conditions.
Specifications
Copyright © 2017 WyreStorm Technologies |
wyrestorm.com
NHD-230-TX Quickstart Guide | 170908
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
4 of 4
Power
Power Supply
12V DC 1A
PoE
IEEE 802.3af 12V 1A 12.95W
Max Power Consumption
10.5W (DC adapter)
Environmental
Operating Temperature
32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%,
non-condensing
Storage Temperature
-4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%,
non-condensing
Maximum BTU
35.82 BTU/hr
Dimensions and Weight
Rack Units/Wall Box
1U
Height
43.5mm/1.72in
Width
220mm/8.67in
Depth
178.5mm/7.03in
Weight
1.2kg/2.64lbs
Regulatory
Safety and Emission
CE | FCC | RoHS
Audio and Video
Inputs
1x HDMI In 19-pin HDMI type A female
Outputs
1x LAN (PoE) 8-pin RJ-45 female, 10/100/1000Base-T Ethernet port LAN (POE)
Output Video Encoding
H.264/MPEG-4 AVC
Encoding Data Rate
2~10Mb/s
End to End Latency
Decoder dependent – Encode latency of 150ms
Audio Formats
In: RAW (PCM 48KHz)
Out: LPCM (1.6Mb/s); AAC (32~240Kbps)
Video Resolutions (Max)
HDMI
1920x1200 @60Hz 8bit (15m/50ft)
1920x1080p @60Hz 8bit (7m/23ft)
Using
Cat6
1920x1080p @60Hz 8bit (100m/328ft)
Color Depth
1080p: 8bit
Maximum Pixel Clock
HDMI: 150MHz
Streaming Formats
Encapsulation Format
MPEG-2 transport stream
Transmission Format
TS over UDP | TS over RTP
Transmission Method
Unicast | Multicast | RTP over RTSP
Session control
RTSP (SETUP, TEARDOWN, OPTIONS, PLAY, DESCRIBE)
Communication and Control
HDMI
HDMI 1.4 | HDCP 1.4
Ethernet
1x 8-pin RJ-45 female | 10/100/1000BaseT | PoE
Troubleshooting
Before Performing any of the Following Troubleshooting Steps
• Verify that all NHD devices contain the latest version of firmware. This
will ensure that all devices are up to date and working at their highest
performance level.
Cannot access the devices web UI or transport stream
• Verify that the
Network Settings, Video Settings,
and
Audio Settings
are
configured properly based on network and content requirements.
• Use another device and attempt to access the web UI or unicast transport
stream to check your device settings are correct
• Attempt to ping the unit on the IP address you set during configuration
• Reboot the unit and again attempt to access the web UI or transport stream
• Disconnect the unit from the network and connect you PC directly (setting a
static IP address on your PC) and try again
• If the above is not successful factory reset the unit and login using the
default IP 192.168.11.243
• If using a non-managed network and multicast is not required set this
address to 0.0.0.0 to avoid bogging down the network.
No Source Appearing on Displays
• Verify that the NHD-230-TX, Network, Source, and Display devices are
powered On.
• Test sources and displays by connecting them directly together.
• Swap out the HDMI cable
• Connect a power supply to the NHD-230-TX rather than using PoE.
All Devices on Network Slow or Unresponsive
• If using a non-managed network and multicast is not required set this
address to 0.0.0.0 to avoid bogging down the network.
