Copyright © 2022 WyreStorm
Pro AV Corporation
|
NetworkHD Quickstart Guide | 221019
INT: +44 (0) 1793 230 343 | US: 844.280.WYRE (9973)
2 of 2
Setup and Configuration
Audio Wiring
NetworkHD uses three different audio outputs. A 3.5mm (1/8in) TRS Stereo Jack audio connection, a 3-pin phoenix unbalanced audio connection and a 5-pin
phoenix balanced audio connection.
NetworkHD Console Configuration (NHD-000-CTL)
In addition to the steps below, more information on configuration can be found in the
NetworkHD Installation Guide.
•
Connect a computer running Windows 7 or newer to the same LAN/VLAN as the NetworkHD components and ensure its IP is within the same subnet as
the NetworkHD. The NHD-000-CTL is set to a static address of
169.254.1.1
by default – do not choose this address for your PC.
•
Power on the NetworkHD devices by connecting the included power supplies to the Power Input or by powering on the PoE switch.
•
Open the WyreStorm Management Suite (Available from the WyreStorm website) and launch the
NetworkHD 000 Series Console
and press search
Note:
If a no devices are discovered, verify that encoders/decoders, CTL and PC are within the same subnet scope and within the same range of the
CTL's AV Port and disable or create an exception for the NetworkHD Console in the Windows Firewall.
•
Configure the system as per the instructions in the NetworkHD Installation Guide.
Devices that use a 3.5mm:
Devices that use a 3-pin:
Devices that use a 5-pin:
NHD-400-TX
NHD-400-DNT-TX
NHD-500-TX
NHD-500-DNT-TX
NHD-600-TX/RX
NHD-110-TX/RX
NHD-110-RX-S
NHD-250-RX
NHD-400-RX v3
NHD-500-TX/RX
NHD-500-DNT-TX
NHD-600-TRX
NHD-600-TRXF
NHD-610-TX/RX
Tip:
Ring:
Left Channel
Right Channel
Sleeve: Ground (GND)
3rd Party Device
Pin 1 L (Left Signal)
---> To ---> Left Signal (L+)
Pin 2 R (Right Signal)
---> To ---> Right Signal (R+)
Pin 3 GND (Ground)
---> To ---> Left Ground (L-)
Right Ground (R-)
WyreStorm Connector
3rd Party Device
Pin 1 Left Positve (L+)
---> To ---> Left Positive (L+)
Pin 2 Left Negative (L-) ---> To ---> Left Negative (L-)
Pin 3 Ground (G)
---> To ---> Ground (G)
Pin 4
Right Positive (R+) ---> To ---> Right Positive (R+)
Pin 5
Right Negative (R-) ---> To ---> Right Negative (R-)
WyreStorm Connector
IMPORTANT! Installation
• Do not connect the power supply until all NetworkHD devices are connected to the network switch.
• NetworkHD Series uses DHCP to assign IP addresses by default. In the absence of a DHCP server an AutoIP address will be assigned in the subnet
169.254.0.0/16. Ensure the PC being used for configuration obtains an IP via DHCP or is set to an address in the AutoIP range prior to starting the
configuration process.
• In order to configure the NetworkHD encoders and decoders, the AV port on the NHD-CTL MUST be connected to the same LAN/VLAN and Subnet as the
NetworkHD encoders and decoders.
• In order for the devices in the system to be controlled via a 3rd party controller on a different VLAN, the CONTROL port MUST be connected to the same LAN/
VLAN and Subnet as the control system.
• The NHD-CTL’s two Ethernet ports are designed to be used in different Networks or VLANs. When using a single Network or VLAN for example when using
NetworkHD Touch - do not connect both ports - only use the AV port of the CTL.
• Install NetworkHD devices to allow airflow through the product - WyreStorm recommends using the NetworkHD rack mounts. The install location should be
dry, well ventilated and guaranteed to maintain the mandatory operating temperature range of the product.
Note:
WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without
prior notice. For full specifications for individual NetworkHD products, visit
NHD-CTL-PRO
The NHD-CTL-PRO setup differs than a system using the NHD-000-CTL. All configurations for NetworkHD endpoints are performed from the
controller's web interface. The default IP address of the AV Port is
169.254.1.1
and the default IP of the CTRL port is
192.168.11.243
. Once
logged in use admin for both the username and password. Follow the on screen prompts to begin setup.
Warranty Information
WyreStorm Technologies ProAV Corp warrants that its products to be free from defects in material and workmanship under normal use for a
period of five (5) years from the date of purchase. Refer to the Product Warranty page on
for more details on our limited
product warranty.
IR TX/RX Guidelines
• Using WyreStorm infrared emitters and receivers is the best way to ensure that most IR coding formats are transmitted and received by the NetworkHD
system. Other 3rd party emitters and receivers can be used; however, these devices must operate in the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports should never be connected directly to a NetworkHD system as an incompatibility may
exist. WyreStorm offers a cable that compensates for voltage differences as well adjusts for differences in the pins used within the port. Refer to the
CAB-IR-
LINK
product page for more information.
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
Tip:
Anode (IR Signal)
Sleeve: Cathode (Ground)
Tip:
Ring:
IR Signal
+5V DC
Sleeve: Ground (GND)
