Warranty Information
This product is covered by a 3 year limited parts and labor warranty. During this period there will be no charge for unit
repair, component replacement or complete product replacement in the event of malfunction. The decision to repair
or replace will be made by the manufacturer. This limited warranty only covers defects in materials or workmanship
and excludes normal wear and tear or cosmetic damage.
Visit the product page located at
wyrestorm.com
for additional information on this product including important
technical information not provided in this document and warranty terms & conditions.
Specifications
Audio and Video
Inputs
1x HDBaseT 8-pin RJ-45 female
Outputs
1x HDMI 19-pin type A
Audio Formats
2ch PCM | Up to 7.1 DTS-X and Dolby
Atmos
HDMI Resolutions
(Max)
1920x1080 @60Hz 48bit (15m/50ft)
4096x2160p @60Hz 24bit 4:2:0 (7m/23ft)
HDBaseT Resolutions
(Max)
HDMI
1920x1080p @60Hz 48bit (15m/50ft)
3840x2160p @24/25/30Hz 4:4:4 24bit
(7m/23ft)
3840x2160p @24Hz 4:2:0 HDR 30bit
(3m/9.8ft)
4096x2160p @60Hz 24bit 4:2:0 (7m/23ft)
Using Cat6/6a/7
1920x1080p @60Hz 36bit (70m/230ft)
3840x2160p @24/25/30Hz 4:4:4 24bit
(35m/115ft)
3840x2160p @24Hz 4:2:0 HDR 30bit
(35m/115ft)
4096x2160p @60Hz 4:2:0 24bit
(35m/115ft)
Color Depth
1080p: 48bit | 4K UHD: 24bit | HDR @24p:
30bit BT.2020
Maximum Pixel Clock
HDMI: 600mHz | HDBaseT: 297mHz
Communication and Control
HDMI
HDCP 2.2 | EDID | CEC | DVI/D with adapter
(not included)
HDBaseT
1x 8-pin RJ-45 female | HDCP 2.2 | EDID |
PoH | Bidirectional IR
IR
1x 3.5mm (1/8in) Mono – IR TX
1x 3.5mm (1/8in) Stereo – IR RX
Bidirectional over HDBaseT (IR TX/IR RX)
RS-232
1x 3-pin Screw Down Phoenix Connector |
Bidirectional over HDBaseT and Firmware
update
Power
Power Input (Optional)
Input: 100~240V AC 50/60Hz
Output: 12V DC 1.5A
Max Power
Consumption
6.6W
PoH
48V 15.4W
Copyright © 2015 WyreStorm Technologies |
wyrestorm.com
MX-0404-HDBT-H2-KIT Quickstart Guide | 160719
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
4 of 4
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
•
Verify that power is being supplied to the matrix and HDBaseT
receivers and that both devices are powered on.
Note:
When using PoH, to power the receivers, verify that the HDBaseT cable is
properly terminated per the
HDMI/HDBaseT Wiring
section.
•
Verify that the matrix, receiver, and display support the output
resolution of the source. Refer to Video Resolutions in the
Specifications
table.
• Configure
EDID Settings to a lower resolution.
•
If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K
rated.
•
Verify that the HDBaseT cable is properly terminated per the
HDMI/
HDBaseT Wiring
section.
•
Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
•
Verify that the IR cable(s) is properly terminated. See
IR Wiring
.
•
Verify that the IR emitter is located near the IR receiver on the device.
Troubleshooting Tips:
•
WyreStorm recommends using a cable tester or connecting the cable
to other devices to verify functionality.
•
Use a flashlight to locate the IR receiver behind any tinted panels on
the device being control.
Environmental
Operating Temperature
32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
Storage Temperature
-4°F ~ 158°F (-20°C ~ 70°C)
10% ~ 90%, non-condensing
Maximum BTU
22.52 BTU/hr
Dimensions and Weight
Rack Units/Wall Box
1U
Height
18mm/0.71in
Width
181.7mm/7.16in
Depth
94mm/3.71in
Weight
0.4Kg/0.88lbs
Regulatory
Safety and Emission
CE | FCC | RoHS
Summary of Contents for MX-0404-HDBT-H2
Page 2: ......
