background image

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

 

1. Read the manual carefully, and use the cleaner according to the manual. We are not liable for any

loss or injury caused by improper use.

 

2. Only use the accessories recommended or sold by the manufacturer.

3. This model only applies to swimming pools with a flat floor.

4. Do not allow children to ride on the cleaner or play with it as a toy.

5. Use the original and authorized charging adapter only.

6. The adapter cord should only be repaired or replaced by a qualified electrician.

7. Do not turn on the cleaner when it is out of water.

8. The  charging  adapter  must  be  connected  to  a  leakage  protected  and  earthed  socket  when

charging.

 

9. Do not operate the cleaner when there are people in the pool.

10. Always clean and wash the filter tray after use.

11. Turn off the cleaner when maintaining, cleaning or when it is not in use.

12. The cleaner should be stored in a cool and ventilated place, away from direct sunshine.

13. While charging, the cleaner should be kept in a cool place, and not be covered with anything to

prevent the damage of internal electrical components caused by overheating.

 

14. Only certified professionals can disassemble the sealed driving kit of the cleaner.

15. Do not operate the cleaner while pool filter is running.

16. Oil seals for motor contain grease, which may cause water pollution if grease leaks occur.

17. Due to the limitation of battery capacity, the cleaner is only suitable for swimming pools with

size up to 500 ft

²

 (46.4m

²

), otherwise the cleaning effect will be affected.

 

18. When the cleaner is stored for a long period of time, it should be charged every three months to

maintain battery life between 40%-60%. Please use the original and authorized charging adapter 

only. If the cleaner is not charged for a long time, the battery voltage will be lower than the over-

discharge protection voltage due to the self-discharge of the battery, which may cause fatal damage.

 

19. Do not use or store the cleaner near any heat source.

20. Do not pierce the shell of the cleaner with nails or other sharp objects. Do not hammer, impact,

or throw the cleaner.

 

21. Make sure the charging socket is dry before charging.

SAVE THESE INSTRUCTIONS

 

Summary of Contents for WY1102















Reviews: