manualshive.com logo in svg

wsm wg972-e4, Workshop Manual

Share
Download
wsm wg972-e4 Workshop Manual Download Page 78

ENGINE

WG972-E4, WSM

1-M17

[7]  REGULATOR WITH VAPORIZER (GAS LINE) 

[WG972-GL, WG972-L, WG972-N]

Regulator with vaporizer evaporates the liquid fuel

(LPG / CNG) into the gaseous fuel and then sends to the
mixer. Regulator with vaporizer has the following
structures and functions.

Evaporator

Evaporator has a long fuel passage to evaporate

liquid fuel to gaseous fuel.

Hot Water Line

The coolant water of the engine is made to circulate

as a heat source to prevent freezing of vaporizer by
latent heat of vaporization.

Primary Stage

There is a primary valve which is safety device for

abnormal pressure.

Secondary Stage

Secondary stage has a secondary valve and controls

the quantity of gaseous fuel flowing to the mixer.

9Y1211108ENM0033US0

A: Secondary Stage
B: Evaporator

C: Primary Stage
D: Hot Water Line

KiSC issued 07, 2015 A

Summary of Contents for wg972-e4


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands