wsm wg972-e4 Workshop Manual Download Page 126

Page: 126 / 153

ENGINE

WG972-E4, WSM

1-S35

Bearing Case Cover

1. Remove the bearing case cover mounting screws. First, remove

inside screws (1) and then outside screws (2).

2. Remove the bearing case cover (6).

(When reassembling)

• Fit the bearing case gasket (3) and the bearing case cover

gasket (4) with correct directions.

• Install the bearing case cover (6) to position the casting mark

"UP"

(a)

on it upward.

• Apply engine oil to the oil seal (5) lip and be careful that it is not

rolled when installing.

• Tighten the bearing case cover mounting screws with even

force on the diagonal line.

9Y1211108ENS0057US0

Tightening torque

Bearing case cover
mounting screw

9.81 to 11.3 N·m
1.00 to 1.15 kgf·m
7.24 to 8.31 lbf·ft

(1) Bearing Case Cover Mounting

Screw (Inside)

(2) Bearing Case Cover Mounting

Screw (Outside)

(3) Bearing Case Gasket
(4) Bearing Case Cover Gasket

(5) Oil Seal
(6) Bearing Case Cover

(a) Top Mark "UP"
(b) Upside

KiSC issued 07, 2015 A

Summary of Contents for wg972-e4


























































































































































Search results

Summary of Contents for wg972-e4

Reviews:

Brands by name

Popular brands

wsm wg972-e4, Workshop Manual

Search results

Summary of Contents for wg972-e4

Reviews:

Brands by name

Popular brands