manualshive.com logo in svg

Wren Kitchens Vogue WALL UNIT 150 Tall 1 Door, Assembly Manual, Page: 8 / 8

Share
Download
Wren Kitchens Vogue WALL UNIT 150 Tall 1 Door Assembly Manual Download Page 8

Page 7

WALL UNIT

150 - 600 Tall 1 Door Assembly Guide

Step 20.

Insert hinge in top & bottom 
holes as shown below. 

Step 21.

Secure hinges by tightening 
2 x screws with hinge dowels 
attached. These are already 
positioned within the hinges.

Step 22.

Attach the door to unit 
where required. To attach 
door, clip hinge onto hinge 
plate and click to secure.

Hinge Cover Caps

Step 24.

Fit cover caps to hinge. 
Adjust Soft close to suit.

Step 23.

Adjust hinge to suit. As shown below.

To 

adjust

 hinge using 

a screw driver, tighten 
or loosen as required at 
points 

1

 & 

2

.

Point 

1

 - In - Out 

Point 

2

 - Left - Right

1

2

FRONTAL 
HINGE 
ADJUSTMENT

Hinge Plates

View from inside of unit

To 

release

 door,

pull catch as shown,
to release hinge from 
the hinge plate.

The top and bottom 

hinges 

MUST

 be 

adjusted to the 

SAME 

STRENGTH.

To 

Move

 the 

hinge up/down, 
loosen screws 
A + B, 
Manoeuvre 
the door, then 
re-tighten the 
screws

A

B

Summary of Contents for Vogue WALL UNIT 150 Tall 1 Door









Reviews:

No comments