manualshive.com logo in svg

Wren Kitchens Vogue WALL UNIT 1000 Lift, Assembly Manual, Page: 9 / 12

Share
Download
Wren Kitchens Vogue WALL UNIT 1000 Lift Assembly Manual Download Page 9

Page 8

For Internal Use: FI.WR.INS.033_WKIN00122_WALL_1000_Lift_Extractor_Housing_Rev8.indd

Care to be taken. Hanging procedure is necessary for a safe installation.

Step 21.

Measure appropriately and 
attach the 2 x hanging bracket 
plates onto the wall screwing 
through the provided holes into 
your wall. 

Step 22.

Hang the unit using the 
brackets to hook onto the 
plate as shown

Hanging Bracket

Plate

Step 23.

Using points a, b & c adjust the unit to suit.

Step a.

Rotate the screw clockwise 
to move the unit up. 
Anti-clockwise for down.

Step b.

Adjust the depth using 
centre screw.

Step c.

Screw the red screw until it 
touches the plate to lock 
in position.

Hanging 

Bracket

viewed through

Back Panel

b

C

c

a

a

b

K

Step 24 .

Screw into any side units using the provided 2x 30mm screws 

(K)

 to secure the 

unit. Screw just to the rear of the hinge plate then place a cover caps 

(M)

 on the 

head to conceal it.

Screws for attaching to walls are not provided as these vary depending on materials, 

thickness and construction. Ensure appropriate fixings for wall construction are used. 

Summary of Contents for Vogue WALL UNIT 1000 Lift













Reviews:

No comments