manualshive.com logo in svg

Wren Kitchens Vogue WALL UNIT 1000 Lift, Assembly Manual, Page: 6 / 12

Share
Download
Wren Kitchens Vogue WALL UNIT 1000 Lift Assembly Manual Download Page 6

Page 5

WALL UNIT

1000 Lift Assembly Guide

 

Step a

Insert hanging 

bracket

 

into pre-drilled holes

Step c

Secure with provided  

2 x 20mm screws 

(S)

 per bracket

Step b 

 Rotate locking 

lever 180 degrees

Detail A

Detail A

S

S

Detail A

Step 13. 

Hanging Brackets steps a,b & c to be carried out on both sides as shown

A

B

Step 14.

Secure corner gussets to the bottom left and right hand 
side of the wall unit using 4 x 15mm screws

 (L)

 per plate.

L

L

L

L

Detail B

View though

Back Panel

Pilot

hol

e

M

Detail B

Step 15.

Drill a small pilot hole through the centre of the corner 
gussets. Use this hole at the end of the process to screw 
through and into the wall. Cover the screw heads using the 
cover caps 

(M)

 provided. 

 

Screws for fixing to walls are not provided as these vary 
depending on your wall 

material and construction. Ensure 

appropriate fixings for wall constructions are used.

Summary of Contents for Vogue WALL UNIT 1000 Lift













Reviews:

No comments