background image

Cordless rotary hammer

  

 

WX382 WX382.1 

 

WX382.2 WX382.3 WX382.4

 

13

condition. Where possible use a pilot hole 
before drilling a large diameter hole.

PROBLEM SOLUTION

REASoNS FoR DIFFERENt BAttERy 

PACK WoRKING tIMES

Charging time problems, having not used a 
battery pack for a prolonged time will reduce 
the battery pack working time. This can be 
corrected after several charge and discharge 
operations by charging & working with your 
drill. Heavy working conditions such as large 
screws into hard wood will use up the battery 
pack energy faster than lighter working 
conditions. Do not re-charge your battery pack 
below 0

o

C and above 30

o

C as this will affect 

performance.

MAINTENANcE

 

Remove the battery pack from the tool 

before carrying out any adjustment, 

servicing or maintenance.

Your power tool requires no additional 
lubrication or maintenance ,except for the 
cleaning & lubrication of the SDS bits and 
adaptors before inserting into the chuck.. 
There are no user serviceable parts in your 
power tool. Never use water or chemical 
cleaners to clean your power tool. Wipe clean 
with a dry cloth. Always store your power tool 
in a dry place. Keep the motor ventilation slots 
clean. Keep all working controls free of dust. 
Occasionally you may see sparks through the 
ventilation slots. This is normal and will not 
damage your power tool.  

ENVIRONMENTAL 

PROTEcTION

Waste electrical products should not 
be disposed of with household waste. 
Please recycle where facilities exist. 

Check with your local authorities or retailer for 
recycling advice.

DISPOSAL OF AN 

EXhAUSTED BATTERY 

PAcK

Li

To preserve natural resources, please 
recycle or dispose of the battery pack 
properly. This battery pack contains 

Li-Ion batteries. Consult your local waste 
authority for information regarding available 
recycling and/or disposal options. Discharge 
your battery pack by operating your tool, then 
remove the battery pack from the tool housing 
and cover the battery pack connections with 
heavy-duty adhesive tape to prevent short 
circuit and energy discharge. Do not attempt 
to open or remove any of the components.

Summary of Contents for WX382

















Reviews: