Worx WG753, Manual

Page: 14 / 16

14
Cordless Lawn Mower EN
Two, three or four
green lights are
illuminated.
The two batteries have a remain-
ing charge. The more lights are
illuminated, the more battery
capacity.
Only one green
light ( ) is
illuminated.
The battery level of at least one
battery pack is very low. Please
check and charge the battery
pack.
No light is
illuminated.
At least one battery is not fully
installed or battery may be defec-
tive.
Only one light is
flashing twice per
cycle.
At least one battery is over
discharged (please refer to the
battery charge condition), please
recharge the two batteries at
once before use again or storage.
Only one light is
flashing three times
per cycle.
At least one battery is hot, wait
for them cool down before start
again.
Only one light is
flashing four times
per cycle.
The machine is over load. Raise
the cutting height or push slowly.
MULCHING MOWING TIPS
When using the mulching plug, your new mower is designed to
cut the grass clippings into small pieces and distribute them
back into the lawn, using mulching fins located inside the mower
deck.
Under normal conditions, the mulched grass will biodegrade
quickly to provide nutrients to the lawn. Please review
the following recommendations for optimum mulching
performance,
1) Avoid mowing when the grass is wet from rain or dew.
Wet grass may form clumps which interfere with the
mulching action and reduce runtime. The best time
to mow grass is in the late afternoon when the grass
is dry and the newly cut area will not be exposed to
direct sunlight.
2) For best mulching performance, set the cutting
height to remove about one third of the grass blade
length, ideally no more than 1.5” at one time. If the
lawn is overgrown, it may be necessary to increase
the cut height to reduce the pushing effort and
prevent overloading the motor. For extremely heavy
mulching, it is advisable to first cut at a high cut
height setting, and then re-cut to the final cut height.
Otherwise, make narrower cuts and mow slowly.
3) For best performance, keep the mower housing free
of built-up grass. From time to time turn mower off,
remove batteries and wait for the blade to come to
a complete stop. Turn mower on its side. Using an
object such as a stick, wipe out any accumulation
of grass in the blade area. Be careful of the sharp
edges of the blade. Clean often in wet, new grass, and
always after every use.
4) Certain types of grass or grass conditions may
require that an area be mulched a second time to fully
disperse the grass throughout the lawn. If cutting
a second time, it is advisable to cut perpendicular
(across) the first cut pattern. DO NOT CHANGE CUT
PATTERN IN ANY WAY THAT WOULD CAUSE MOWING
DOWN A HILL.
5) Change your cutting pattern from week to week. This
will help prevent matting and graining of the lawn.
CUTTING AREA
The cutting area can be affected by many factors including:
cutting height, operation practices (ex: starting/stopping),
lawn moisture levels, grass length and thickness.
It is ideal for mowing ¼ acre to
1
/2 acre lot sizes.
TIPS:
1) Mowing the lawn frequently and reducing the amount
of starting/stopping procedures will help conserve battery
runtime. It is recommended to always use the same two
batteries during operation with fully charged levels.
2) For the best cutting performance, it is recommended to
only mow up to 1/3 or less of the current grass height at a time.
Mow at a slower pace when cutting long/thick grass to allow
the mower to properly discharge the clippings.
MAINTENANCE
WARNING: Stop the mower and remove
batteriesbefore removing the grass collection
bag.
NOTE: To ensure long and reliable service, perform the
following maintenance procedures regularly. Check for
obvious defects such as a loose, dislodged or a damaged
blade, loose fittings, and worn or damaged components.
Check that the covers and guards are all undamaged and
are correctly attached to mower. Carry out any necessary
maintenance or repairs before operating mower. If the mower
should happen to fail despite regular maintenance, please call
our customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY OR MULCH
PROPERLY.
WEAR PROPER EYE PROTECTION WHILE REMOVING,
SHARPENING, AND INSTALLING BLADE. ENSURE THE
BATTERIES ARE REMOVED.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand
causes the blade to dull quickly. If your lawn has sandy
soil, more frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. N)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to keep
it balanced, removing equal amounts of material from
both ends.
NOTE:
1. Be sure the mower is turned off and remove the key.