11
10
11
10
Electric lawn mower
EN
Mow the lawn at a right angle from the power
supply and place the power cable to side
which has already been cut.
NOTE: The motor is protected by a safety
cut out which is activated when the
blade becomes jammed or if the motor is
overloaded.
When this occurs stop, remove the plug from
the power supply.
Release the switch lever,
Clear any obstruction, then restart it.
If the mower cuts out again increase the
height of cut to reduce the load on the motor.
wARNING!
When mowing do not allow
the motor to labor particularly in heavy
conditions. When the motor labors the speed
of the motor drops and you will hear a change
in the motor sound, when this occurs, stop
mowing, release the switch lever and raise the
height of cut. Failure to do so could damage
the machine.
3. GRASS bAG FILLING INDICATOR(3)
(See Fig. F)
To remind you immediately to empty when
the grass bag is full, the mower provides
an indicator on the top of bag to show the
collection status. And you can follow as
below:
Empty status: flap floats (a)
Fully status: flap falls down (b)
4. INSTALLING mULChING PLUG (12)
(See Fig. G)
1)
Switch off the mower and Unplug
from the mains,
and wait for
blade(14) to come to a complete stop.
2) Raise the safety guard and hold it up.
3) Slide the Mulching Plug into the discharge
opening until it is firmly in contact with the deck.
4) Release safety guard and ensure it is
properly closed.
5. REmOVING mULCh PLUG (See Fig. G)
To remove the Mulching Plug so that you can
collect the grass follow the steps listed below:
1)
Switch off the mower and Unplug
from the mains,
and wait for blade to
come to a complete stop.
2) Raise the safety guard and hold it up.
3) Grasp the middle of the plug, lift and pull
out the Mulching Plug completely.
4) The safety guard is spring loaded. When
you release it, the guard will return to the
closed position.
6. REAR DISChARGE (See Fig. h)
The mower provides a rear discharge function,
so that you can mower without bag collection.
The debris will be discharged from the rear
chute.
7.wORK mODE DIAL(15) (See Fig. I)
Status1: QUIET mode
Select QUIET mode when mowing in everyday
conditions, removing approximately 20mm of
grass at a time.
Status2: TURbO mode
Set the dial to TURBO mode when cutting
dense or overgrown grass.
ImPORTANT!
The TURBO function is only
activated when mowing. When select TUROB
or Quiet mode, the motor speed will have a
change when mowing
8. ADJUSTING ThE CUTTING hEIGhT
(See Fig. J)
wARNING!
STOP REALEASE THE
SWITH LEVER, UNPLUG TOOL, AND
WAIT FOR BLADE TO COME TO A COMPLETE
STOP .The blades continue to rotate after the
machine is switched off, a rotating blade can
cause injury.
CAUTION:
Do not touch rotating blades.
The lawn mower can be set to 6 cutting heights
between 20mm and 70mm. For this purpose,
move the cutting height adjustment lever
outwards then adjust to the preferred position
9. mULChING mOwING TIPS
While mulching, your new mower is designed
to cut the grass clippings into small pieces
and distribute them back into the lawn. Under
normal conditions, the mulched grasses will
Summary of Contents for WG707E
