background image

8

    Limited Warranty

World LIMITED FIVE – YEAR WARRANTY.

 World Warm Air Hand Dryer, Model covered in this manual, is warranted by World Dryer Corporation to the origi-

nal user against defects in workmanship or materials under normal use for 5 years after date of purchase excluding normal wear and tear, or expendable parts such 

as HEPA filters, motor brushes, etc. Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as World 

designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at World’s option. For limited warranty claim procedures, see PROMPT 

DISPOSITION below. This limited warranty gives purchasers specific rights from jurisdiction to jurisdiction.

LIMITATION OF LIABILITY. 

To the extent allowable under applicable law, World’s liability for consequential and incidental damages is expressly disclaimed. 

World’s liability in all events is limited to and shall not exceed the purchase price paid.

WARRANTY DISCLAIMER. 

 World has made a diligent effort to provide product information and illustrate the products in this literature accurately; however, 

such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are MERCHANTABLE, or FIT FOR 

A PARTICULAR PURPOSE, or that the products will necessary conform to the illustrations or descriptions. Except as provided below, no warranty or affirmation on 

fact, expressed or implied, other than as stated in the “LIMITED WARRANTY” above is made or authorized by World.

PRODUCT SUITABILITY.

 Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes, 

which may vary from those in neighboring areas. While World attempts to assure that the products comply with such codes, it cannot guarantee compliance, and can 

not be responsible for how the product is installed or used. Before purchase and use of a product, review the product application, and all applicable national and local 

codes and regulations, and be sure that the product, installation, and use will comply with them.

Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the exclusion or limitation of incidental or consequen

-

tial damages, so the above limitation or exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation on how long an implied warranty lasts, 

consequentially the above limitation may not apply to you; and (c) by law, during the period of this Limited Warranty, and implied warranties of implied merchantability 

or fitness for particular purpose applicable to consumer products purchased by consumers, may not be excluded or otherwise disclaimed. 

Manufactured by World Dryer Corporation, Berkeley, Illinois 60163 U.S.A

PROMPT DISPOSITION.

 World will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be defective 

within limited warranty. For any product believed to be defective within limited warranty, first write or call dealer from whom the product was purchased. Dealer will 

give additional directions. If unable to resolve satisfactorily, write to World at address below, giving dealer’s name, address, date, and number of dealer’s invoice, and 

describing the nature of defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was damaged in transit to you, file claim with carrier.

Dryer fails to start.

Incoming Power Supply

Remove cover and check diagnostic LEDS.  If no 

LED’s are lit, check power supply at the circuit 

breaker / fuse. 

Defective PCB

If no LED’s are lit above and supply circuit is con-

firmed to be active, replace PCB and transformer.

Sensor Obstruction

If LED 5 is lit or flashing (Green) 

without hands 

under the sensor

, check Sensor Lens for foreign 

material or dirt. Clean Lens with soft damp cloth 

and mild cleaning agent

Defective Sensor Operation

If LED 5 does not light when hands are under 

sensor, replace PCB and sensor.

Motor Brushes at End of Service Life

Check motor brushes and replace if necessary.

Defective Heating Element

(

Important:

 Applies only when 

connected to 208 – 240V power supply)

If dryer is connected to 208 – 240V power supply 

and all other possible causes have been checked, 

replace the heating element.

Dryer too loud.

Dryer Speed Setting

Adjust blower speed to “Low”.  See page 4.  When 

operating at low speed, LED 4 will light (blue) 

when hands are under sensor.

Air temperature is too cold. The dryer’s 

heating fluctuates / goes “on” and “off” during 

a drying cycle. The dryer speed fluctuates 

up and down during a drying cycle.

Defective Heating Element

(

Important:

 Applies only when 

connected to 120V power supply)

Replace heating element.

Dryer will only run a few seconds and then 

stops. Dryer will not activate every time.

Arcing sound during operation. Funny 

smell (ozone) during operation.

Motor Brushes at End of Service Life

Check motor brushes and replace if necessary.

Defective Heating Element 

(

Important: 

Applies only when con-

nected to 208 – 240V power supply)

Replace heating element.

    Troubleshooting Chart

Summary of Contents for Q-Series VERDEdri










Reviews: