AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909 (toll free)
MODEL No.: IW36 • 61551 • 07/2018
17
AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909 (toll free)
MODEL No.: IW36 • 61551 • 07/2018
16
Important information – Product care
NOTE: Xfinity Battery and Charger not included. For any issues related
directly to your purchased ALDI Xfinity Battery / charger, contact the
Customer Service of the manufacturer as listed on the battery / charger
packaging, manual or on the label on the battery / charger.
This Impact Wrench uses Lithium Ion Battery Cells. Care MUST be taken to ensure
both the safety and life of the pack is maintained. Ensure you have read all of the
safety notes in the previous pages before using the Impact Wrench.
Treat the battery pack with care and within the guidelines of this manual and the
supplied manual included with the purchase of ALDI Xfinity Battery/s.
If the battery pack does become immersed in water or any fluids, or is subject
to a severe drop or it does not operate within the guidelines of this manual
or the supplied manual included with the purchase of ALDI Xfinity Battery/s.
immediately STOP using the battery pack and have it checked. During operation
avoid overloading the Impact Wrench. If the Impact Wrench is overloaded it will
automatically STOP. Overloading may occur for a number of reasons including
when the Impact Wrench is pushed too hard or when using an Impact Wrench bit
or attachment greater than what is specified. If you do overload the drill/driver
during operation refer to the “Overload” section in this manual.
NOTE: When the battery of the Impact Wrench is at the lower end of the charge,
the Impact Wrench is more susceptible to the overload condition. Running the
Impact Wrench at close to maximum load, or continual resetting of the overload
will cause the battery pack to overheat. When a preset cell temperature is
detected, the battery pack will automatically STOP operating and will not restart
until the battery pack has cooled to a safe level.
In this condition, DO NOT force cool the pack by placing in a freezer or similar
device. Refer to the “Overload” section in this manual.
Another feature of the Impact Wrench is the low voltage cut out feature. This
feature operates when the voltage drops below a preset value. When this occurs
the tool will automatically stop operating. To correct the situation you need to
either insert another charged battery into the Impact Wrench or recharge the
existing battery, and then proceed with the Impact Wrench application.
NOTE: Attempting to restart the tool in this condition without either recharging
the battery or installing a battery with charge will lead to Impact Wrench
restarting and then stopping again after only a few seconds of operation.
These safety devices have been fitted for the safety, reliability and life of the tool.
Assembly
Fitting and removing the Battery Pack from the Impact
Wrench and Charger.
NOTE: (Xfinity Battery pack and charger is not included with
this product; it is shown only for illustrative and instructional
purposes only)
1. To install your purchased Xfinity battery pack (6) on to the impact
wrench, align the grooved guide rails of the battery pack (6) with the
raised guide rails on the bottom of the impact wrench. With your
thumb on the battery release tab on the battery pack, slide it firmly into
the handle until the battery is secure in position (Fig A). Release your
thumb from the battery release tab. When the battery is secured you
will hear it engage with a snap / click.
2. To remove the battery pack (6) from the impact wrench, press the
battery pack release button and slide the battery pack (6) completely
out and away from the impact wrench (Fig B).
3. When applying the battery pack (6) onto your purchased Xfinity
charger (7), align the grooved guide rails of the battery pack (6) with the
raised guide rails on the charger (7) (Fig C). The charger (7) will make a
snap / click noise when it is securely aligned.
A.
B.
