2400W Wet & Dry Vacuum
AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909
MODEL No.:
MWW706S-35L-1200WC • 06/2018 • 61406
(toll free)
AFTER SALES SUPPORT
(toll free)
2400W Wet & Dry Vacuum
e-mail: [email protected]
1800 909 909
MODEL No.:
MWW706S-35L-1200WC • 06/2018 • 61406
20
21
Operation
Operation
Automatic Mode for Electric Power Tools
1. Connect the flexible hose (17) to the flexible
hose outlet – suction (7) by inserting into the
outlet and aligning the arrow and locking pin on
the end of the flexible hose (17), with the arrow
and ridge on the top of the flexible hose outlet
– suction (7). This should ensure the locking pin
on the flexible hose (17) aligns with the ridge in
the flexible hose outlet – suction (7). Rotate the
flexible hose (17) to the left to secure the hose
into position (Fig Z).
2. Ensure the HEPA filter (16) is secured on the
appliance head (2) (Fig AA).
3. Connect the power cable of your AC / electric
power tool to the AC outlet socket (4) (Fig AB).
The automatic AC outlet socket (4) is ideal for
power tools up to 1200W. Check the rating label
of your power tool before connecting to the AC
socket outlet (4) (Fig Y).
4. Connect the opposite end of flexible hose (17)
to the dust extractor connector on your AC /
electric power tool. Check that the connections
are secure and airtight (Fig AC).
Press the ON/OFF Switch (3) to position “II” -
Automatic Mode (Fig AD).
IMPORTANT: When you switch “ON” the
connected AC / electric power tool, the
vacuum switches ON at the same time.
When you switch “OFF” the connected AC /
electric power tool, the vacuum switches
OFF also (after a pre-set delay).
5. When you have finished your task, press “O”
on the ON/OFF switch (3) (Fig AE).
WARNING: Check the tank (10) regularly
and empty the waste collected when it is
about 2/3 full.
AA.
AB.
AC.
Z.
AD.
AE.
AF.
WARNING: Check the HEPA filter (16) regularly for any blockages
which may reduce the suction and overheat the motor. If the vacuum
noise changes, immediately switch off the appliance and check the
HEPA filter (16). Clean the HEPA filter (16) (instructions can be found on page
23) and empty the tank (10) if required.
* Dust bags (61406-DB) can also be used for dust extraction in Automatic
mode for electric power tools and can be purchased separately as an
accessory. Refer to page 25 for details.
NOTE: For automatic mode ,The Wet & Dry Vacuum is fitted with a thermal
cut-out device, which will automatically turn off the vacuum if the power
of an AC / electric power tool or other device you connected is over
the maximum 1200W. When this happens, immediately switch off the
appliance by pressing on the “O” on the ON/OFF switch (3), disconnect the
power tool, leave the vacuum 5-10 minutes, then,connect the power tool
with rated power up to 1200W. Press the ON/OFF switch (3) to position “II”
-Automatic Mode to continue the job.
Blowing Function
WARNING: Wear a dust mask and eye protection if blowing
creates dust that might be inhaled.
WARNING: Keep bystanders clear from blowing debris.
CAUTION: Any material left in the tank (10) may be blown out, causing injury.
1. Make sure the tank (10) is empty and completely dry before using it as a
blower.
2. Connect the flexible hose (17) to the flexible hose outlet – blowing (8) by
inserting into the outlet and aligning the arrow and locking pin on the
end of the flexible hose (17), with the ridge on the top of the flexible hose
outlet – blowing (8).
