Workhorse PhotoSharp Owner'S Manual Download Page 3

 

Introduction 

3730 E. Southern Avenue, Phoenix, AZ 85040 USA                       

800-778-8779 

Workhorseproducts.com 

Congratulations on your purchase of the PhotoSharp. 

Check the crate for damages. DO NOT accept the crate if there are any damages caused by improper         
handling during shipping. Immediately report any damages to the carrier and contact Workhorse Products at, 
800-778-8779. 

Be sure to inspect the crate contents IMMEDIATELTY, while the carrier is still present. Even though our   
packaging has been designed to handle normal shipping conditions, we cannot foresee damages done by the 
carrier. We will not be responsible for damages that occur during transportation. 

If there are damages immediately notify the driver, file a claim with the carrier and call Workhorse Products. 

The Importance of the Owner’s Manual: 

The purpose of the Owner’s Manual is to familiarize you with the parts and operations of the PhotoSharp. 
There are step-by-step instructions to assemble the press, accompanied with links to videos for further      
assistance. Also included are explanations of the product’s key features, and additional information that will 
help with the maintenance of your press.  

Summary of Contents for PhotoSharp




















Reviews: