touching it. The blade continues to rotate after the trimmer
is switched off; a rotating blade can cause injury.
·
Work only in daylight or in good artificial light.
·
Avoid operating the trimmer in bad weather conditions
especially when there is a risk of lightning.
·
Operating the trimmer in wet grass decreases the efficiency
of performance.
·
Switch off when transporting the trimmer to and from the area
to be worked on.
·
Switch on the motor only when the hands and feet are away
from the cutting means.
·
Do not put hands or feet near the cutting system.
·
Remove battery before blade change.
·
Never fit metal cutting elements to this trimmer.
·
Inspect and maintain the trimmer regularly.
·
Have the trimmer repaired only by an authorized
customer service agent.
·
Always ensure that the
ventilation slots are kept clear of debris.
·
Remove the battery:
–
whenever you leave the machine unattended for any
period of time
–
before replacing the blade
–
before cleaning or working on the trimmer
·
Store the machine in a secure, dry place out of the
reach of children. Do not place other objects on top of the
machine.
·
Replace worn or damaged parts for safety.
·
Ensure replacement parts fitted are approved.
·
Do not operate the machine without the trimmer
attachment fitted.
MOUNTING AND OPERATION
ASSEMBLY
To prevent accidental starting that could cause
serious personal injury, always remove the battery pack from the
product when assembling parts.
ASSEMBLING THE PROCTIVE COVER (see fig. 4)
Step 1: Align the corner to the slot on head housing. Press it into
it entirely.
Step 2: using a cross head screwdriver to fasten screw.
MOUNTING THE BLADE (see fig 5)
Step1: Threr are two holes on the blade, and algn the bigger one
to the screwhead.
Step2: Slide the blade outside according the direction showed in
pic 5. When slide into the smaller hole, it already securily
mounted.
MOUNTING THE AUXILIARY HANDLE
（
see fig 6
）
Step1: Press the spring knob (4) on both sides of the handle
completely.
Step 2: Slide the handle hoop on the handle til the spring knob
(4) pop up, you will hear click then.
ADJUSTMENT OF THE CUTTING ANGLE OF THE HANDLE
(see fig 7)
Step 1: using the finger to slide the knob (5) backward and keep
it.
Step 2: Grasp the main handle and turn it to 90
0
or 180
0
.
ADJUSTMENT OF POLE LENGTH (see fig 7)
Step 1: Loosen the screw knob.
Step 2: Pull the rear handle backward till the desire length.
Step 3: Fasten the screwknob again.
TILTING THE MOTOR HEAD (see fig 9)
Step 1: Press Tilting lock knob (8) and hold it.
Step 2: Move the head up or down to desire angle.
Sttep 3: After get the desire angle, release the tilting locking
knob.
ADJUSTMENT OF AUXILIARY HANDLE (see fig. 10)
Step 1: Press the spring knob (4) and hold it.
Step 2: Move the ausiliary handle left or right till the disre
position.
Step 3: release the spring knob (4).
CHECKING THE BATTERY LEVEL
Press the bottun on the battery pack, and the light will shine. 4
LED shine denotes battery is full, 3 LED shine denotes around
60% full, 2LED shine denotes 40% full, 1LED denotes 20%
full, no LED shine denotes empty.
SWITHING ON/OFF
Swithing on: Press the safety knob (1) and hold it, then press
switch trigger (2), the machine works.
Swiching off: Just release swith trigger (2).
WORKING ADVICE
Battery tools are always in oprating condition.
Therefore, switch should always be in the OFF position when
not in use or carrying at your side.
Cut the grass by swaying the trimmer sideways to the right
and left. Cut slowly while the trimmer is tilted forwards by
approx. 30°.
Cut tall grass by a series of levels from top to bottom.
Watch out for children, pets, open windows, or freshly washed
cars, and blow debris safely away.
After using machines or other equipment, clean up!
Dispose of debris properly.
NOISE/VIBRATION INFORMATION
The vibration level given in this information sheet has been measured in accordance with a standardised test given in EN 60335
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify
additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
MAINTENANCE
