Work area safety
●
Keep work area clean and well lit. Cluttered or dark areasinvite
accidents.
●
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases ordust. Power tools
create sparks which may ignite the dust or fumes.
●
Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
Electrical safety
●
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
●
Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
●
Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
●
Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges and moving parts. Damaged or entangled cords
increase the risk of electric shock.
●
When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
●
If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
Personal safety
●
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in
serious personal injury.
●
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
●
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
●
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
●
Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected
situations.
●
Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
●
If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust-related hazards.
Power tool use and care
●
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer
at the rate for which it was designed.
●
Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
●
Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
●
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
●
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the po
wer tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
●
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
●
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Use and handling of the cordless electrical power
tool
a) Charge a rechargeable battery unit using only the
charger recommended by the manufacturer. Chargers
are often designed for a particular type of rechargeable
battery unit. There is the danger of fire if other types of
rechargeable battery units are used.
b) Only the rechargeable battery units supplied are to
be used with an electrical power tool. The use of other
rechargeable battery units may lead to the danger of
injury or fire.
c) When they are not being used, store rechargeable
battery units away from paperclips, coins, keys, nails,
screws or other small metal objects that could cause the
contacts to be bridged. Short-circuiting the contacts of a
rechargeable battery unit may result in heat damage or
fire.
d) Fluids may leak out of rechargeable battery units if
they are misused. If this happens, avoid contact with the
fluid. If contact occurs, flush the affected area with
water. Seek additional medical help if any of the fluid
gets into your eyes. Escaping battery fluid may cause
skin irritation or burns.
Service
●
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Special Safety Directions for the device
1)
SPECIAL
SAFETY
INSTRUCTIONS
FOR
RECIPROCATING SAWS
•
Hold the electric tool by the insulated gripping
surfaces when performing work in which the cutting
tool may come into contact with hidden wiring
.
Contact with a live wire can also cause a charge in
metal parts of the device and result in an electric shock.
•
Keep hands away from the sawing area. Do not
reach underneath the work piece.
Upon contact with
the blade there is a risk of injury.
●
Only when the electric tool is turned on should the
sawing blade be moved against the work piece.
There is a risk of kickback if the tool insert jams in the
