Worcraft CS2600, Instruction Manual

Page: 71 / 92

3. Start the chain saw by following the starting instructions. (refer
to 6.2 and 6.3)
4. Disengage the chain brake (pull the front hand guard (6)
towards the front handle (7)).(Fig. 5A)
5. Grasp the rear handle (8) with your right hand.
6. After a brief warmup period, run the engine at full speed. With
the back of your left hand, push the front hand guard (6) towards
the guide rail (2). This will engage the chain brake.(Fig. 6)
Danger: Engage the chain brake slowly and carefully.
Hold the saw firmly with both hands, and make sure you have a
good grip. The saw must not touch any objects.
7. The chain (3) must stop abruptly. Immediately release the
throttle lever (11) when the chain (3) has come to a stop.
Danger: If the chain (3) does not stop, shut off the engine and
take the saw to an authorized service center for repair.
Checking the clutch
Carry out a functional check on the clutch on a regular basis. Test
the clutch before the fi rst cut, after several cuts, after
maintenance is done on the chainsaw and if the chainsaw has
been subjected to strong impact or if it has been dropped.
1. Start the chain saw by following the starting instructions. (refer
to 6.2 and 6.3)
2. Briefl y actuate the throttle lever and release it to ensure that
If it is pulled out at an angle, friction will occur on the
eyelet. As a result of this friction, the cable will become
frayed and will wear faster. Always hold onto the starter
handle when the cable retracts. Never allow the starter
handle to snap back when it has been pulled out.
Starting a warm engine (Fig. 7A-7D)
(The chainsaw has been idle for less than 15-20min.)
1. Set the equipment down on a hard, level surface.
2. Move the On/Off switch (10) to the „I“ position.(Fig.
7A)
3. Press the fuel pump primer (23) 10 times.(Fig. 7B)
4. Hold the saw fi rmly and pull out the starter handle (9)
until you feel it start to resist. Then quickly pull the starter
handle (9) several times until the engine starts. The
equipment should start after 1-2 tugs. If the saw does
not start after 6 pulls, repeat steps 1 - 7 of above. (Fig.
7D)
To stop engine
1. Release trigger and allow engine to return to idle
speed.
2. Move STOP switch down to stop engine.
Note: To stop the engine in an emergency, activate the
chain brake and switch the ON/OFF switch
to “Stop (0)”.
MAINTENANCE
Disconnect the spark plug boot before doing any cleaning
and maintenance work!
Cleaning
•
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device immediately
each time you have finished using it.
•
Clean the equipment
regularly with a moist cloth and some soft soap. Do not use
cleaning agents or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into the device.
Maintenance
Warning:
All maintenance work on the chainsaw apart from the
work described in this manual may only be carried out by
authorized after-sales service personnel.
Air fi lter
Note:
Never operate saw without the air fi lter.
Dust and dirt will be drawn into engine and damage it. Keep the
air fi lter clean! The air fi lter must be cleaned or replaced after
every 20 hours of service.
Cleaning the air fi lter (Fig. 8A/8B)
1. Remove the top cover (14) by undoing the cover fastening
screw (A) on the cover. You can then remove the cover (Fig. 8A).
2. Lift out the air fi lter (15) (Fig. 8B).
3. Clean air fi lter. Wash fi lter in clean, warm, soapy water. Rinse
in clear, cool water. Air dry completely.
Note: It is advisable to have a supply of spare fi lters.
4. Insert the air fi lter. Install the air fi lter cover (14). Make sure
that the cover fi ts perfectly when you do so. Tighten the cover
fastening screw.
Fuel fi lter
Note:
Never use the saw without a fuel fi lter. After 100 hours in
operation the fuel fi lter should be cleaned or, in case of damage,
replaced. Be sure to empty the fuel tank before changing the filter.
1. Remove the fuel tank cap.
2. Bend a piece of soft wire.
3. Reach into fuel tank opening and hook fuel line. Carefully pull
the fuel line toward the opening until you can reach it with your fi
Carburetor setting
The carburetor has been set to its perfect adjustment at
the factory. If it requires adjusting, take the saw to your
nearest authorized after-sales service outlet.
7.2.5 Chain bar
•
Grease the guide rail starwheel after
every 10 hours of operation. This is necessary to get the
best performance from your chainsaw.(Fig. 9) Clean the
lube hole, then place the lube gun (not included) at the
hole and pump grease into the bearing until grease is
forced out.
•
Clean the groove which the chain runs in as well as the
oil entry hole on a regular basis using a commercially
available cleaning tool.(Fig. 10A) This is important to
ensure optimal lubrication of the guide rail and chain
during operation.
•
Remove burrs and sharp edges on the guide rail (2) by
carefully filing them down with a flat file. (Fig. 10B)
•
Turn the guide rail (2) around after every 8 hours of
operation so that it wears evenly on the top and bottom.
Oil passages
Oil passages on the bar should be cleaned to ensure
proper lubrication of the bar and chain during operation.
Note: The condition of the oil passages can be easily
checked. If the passages are clear, the chain will
automatically give off a spray of oil within seconds of
starting the saw. Your saw is equipped with an automatic
oiler system.
Automatic chain lubrication.
The chain saw is equipped with an automatic oil
lubrication system with a toothed wheel drive. It
automatically supplies the bar and the chain with the
right quantity of oil. The moment the engine is
accelerated, the oil also starts to fl ow through the bar
plate more quickly as well.
The chain lubrication system has been set to its perfect
adjustment at the factory. If it requires adjusting, take the
saw to your nearest authorized after-sales service outlet.
A setting screw for adjusting the chain lubrication (Fig.
14/ Item A) is located on the underside of the chain saw.