background image

WARRANTY

Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship 

and materials for a period of two years from the date of original purchase by the original owner. This 

warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, 

lack of maintenance, or reimbursement of third party expenses incurred. 

Woodstock International, Inc. will repair, replace, or arrange for a dealer refund, at its expense and 

option, the Shop Fox machine or machine part proven to be defective for its designed and intended 

use, provided that the original owner returns the product prepaid to an authorized warranty or repair 

facility as designated by our Bellingham, Washington office with proof of their purchase of the product 

within two years, and provides Woodstock International, Inc. reasonable opportunity to verify the 

alleged defect through inspection. If it is determined there is no defect, or that the defect resulted 

from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner 

must bear the cost of storing and returning the product. 

This is Woodstock International, Inc.’s sole written warranty and any and all warranties that may be 

implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited 

to the duration of this written warranty. We do not warrant that Shop Fox machinery complies with 

the provisions of any law, acts or electrical codes. We do not reimburse for third party repairs. In no 

event shall Woodstock International, Inc.’s liability under this limited warranty exceed the purchase 

price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be 

tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries 

to persons or property or for incidental, contingent, special or consequential damages arising from the 

use of our products.

Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability 

standards. We are commited to continuously improving the quality of our products, and reserve the 

right to change specifications at any time.

To register the warranty, go to 

https://www.woodstockint.com/warranty

, or scan the QR code below. 

You will be directed to the Warranty Registration page on www.woodstockint.com. Enter all applicable 

production information.

WARRANTY

WOODSTOCKINT.COM

WARRANTY

Summary of Contents for Shop fox W1856





















































Reviews: