Woodstock Shop Fox W1684 Page 4 Instruction Manual Download | Manualshive

Page: 4 / 42

background image

INTRODUCTION

-2-

INTRODUCTION

About Your New Jointer

Your new SHOP FOX

®

Jointer has been specially designed to provide many years of trouble-free service.

Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reli-
able operation.

The Model W1684 is capable of a wide variety of operations, including surface jointing/planing, edge
jointing, beveling and rabetting. The handwheels allow you to make precision table adjustments, the
control panel is easily accessible and the solid, cast-iron cabinet provides a vibration dampening base
for smooth-quality cuts.

Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and dura-
bility of this product be included.

If you have any comments regarding this manual, please feel free to contact us at:

Woodstock Service And Support

We stand behind our machines! In the event that a defect is found, parts are missing or questions arise
about your machine, please contact Woodstock International Service and Support at 1-360-734-3482 or
send e-mail to: [email protected]. Our knowledgeable staff will help you troubleshoot
problems, send out parts or arrange warranty returns.

Woodstock International, Inc.

Attn: Technical Support Department

P.O. Box 2309

Bellingham, WA 98227

«
...
2
3
4
5
6
...
»

Summary of Contents for Shop Fox W1684











































Reviews:

No comments

Related manuals for Shop Fox W1684

Brand: parktool Pages: 2

Brand: laguna Pages: 28

Brand: ELC Pages: 12

Brand: Legacy Pages: 4

Power Xpert Series

Brand: Eaton Pages: 156

Brand: VOLTCRAFT Pages: 8

MAXIMUM 054-1232-4

Brand: MasterCraft Pages: 19

Brand: New World Technologies Pages: 31

Brand: General integration Pages: 12

360 IQ HAT PRESS

Brand: Hotronix Pages: 16

Brand: Yost Vises Pages: 5

Brand: M-system Pages: 4

Millipore mA700

Brand: Merck Pages: 9

Brand: 9circle Pages: 4

Brand: Hama Pages: 54

Brand: tekton Pages: 8

Josef Kihlberg B560

Brand: Signode Pages: 56

Brand: Clarke Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands