manualshive.com logo in svg

Woods TS44, Operator'S Manual

Share
Download
Woods TS44 Operator'S Manual Download Page 9

Safety 

9

MAN0814 (3/11/2010)

4 - P0021

5 - PN 55122

TO AVOID SERIOUS INJURY OR DEATH:

  Read Operator's Manual before operating, 

servicing or repairing equipment. Follow all 
safety rules and instructions. (Manuals are 
available from dealer or call 1-800-319-6637.) 

  Operate from tractor seat only.

  Lower equipment to ground, stop engine, 

remove key and set brake before dismounting 
tractor.

  Never allow children or untrained persons to 

operate equipment.

  Never allow riders.

  Keep bystanders away from equipment during 

operation.

  Keep all shields in place and in good condition.

FAILURE TO FOLLOW THESE INSTRUCTIONS 

CAN RESULT IN INJURY OR DEATH.

55122-C

WARNING

BE CAREFUL!

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a 
pressure washer; high-pressure water can enter 
through very small scratches or under edges of decals 
causing them to peel or come off.

Replacement safety decals can be ordered free from 
your Woods dealer. To locate your nearest dealer, check 
the Dealer Locator at www.woodsonline.com, or in the 
United States and Canada call 1-800-319-6637.

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

7 - 1004299

Summary of Contents for TS44









































Reviews:

No comments

Brands by name

Popular brands

Load more brands