Woods 208-2 Page 36 Operator'S Manual Download | Manualshive

Page: 36 / 74

background image

34

Assembly

32394 (Rev. 9/3/2004)

MOUNTED 208-2 ASSEMBLY

The mounted 208-2 is available for Category 1 and
Category 2, 3-point hitch tractors. It is also available
with single or dual tailwheels.

A-Frame Installation (MTD)

(Figure 26 & Figure 27)

Determine if the machine is to be set up in a Category
1 or 2 configuration. Refer to the proper category
instructions

Figure 26

. Category 1, 3-Point Hitch

Installation (MTD)

Category 1 Assembly (MTD) (Figure 26)

Attach right A-frame half (1) and left A-frame half (2) to
top hole of cutter mast by placing washer (13) and
sleeve (12) on bolt (14). Insert bolt through mast and A-
frame half, then place spacer (3), washer (13), lock
washer (5), and nut (4) on bolt. Torque hardware.

Insert clevis pin (11) through lower hole in top of A-
frame and place a washer (10) on each end. Secure
both ends of clevis pin with cotter pins (9).

Place spacer (7) inside top link weldment (6) and
attach to top hole of A-frame with bolt (8), lock washer
(5), and nut (4). Torque hardware.

Insert category 1 hitch pin (15) through bottom hole of
cutter mast by inserting hitch pin (14) through top hole
of cutter mast and secure with Klik pin (16). Tractor 3-
point arms will be mounter inside the clevis bracket.

Figure 27

. Category 2, 3-Point Hitch

Installation (MTD)

DB2118

CATEGORY 1

3--POINT HITCH MOUNT

1. Right A--frame half
2. Left A--frame half
3. 1--1/8 x 1--7/16 x 11/16” Spacer
4. 3/4” Hex nut
5. 3/4” Standard lock washer
6. Top link weldment
7. 3/4 x 1--1/4 x 3” Spacer
8. 3/4 x 5--1/2” Bolt
9. 1/4 x 1--1/2” Cotter pin

10. 3/4” Flat washer

11. 3/4 x 5--27/32” Clevis pin

12. 3/4 x 1--1/8 x 1--3/8” Sleeve
13. 3/4 x 1--3/4” x 7GA Flat washer
14. 3/4 x 3” Bolt
15. Category 1 hitch pin
16. 7/16 x 11/32” Klik pin

CATEGORY 2

3--POINT HITCH MOUNT

1. Right A--frame half
2. Left A--frame half
3. 3/4 x 1--1/4 x 3” Sleeve
4. 3/4” Hex nut
5. 3/4” Standard lock washer
6. Top link weldment
7. 3/4 x 1 x 3” Spacer
8. 3/4 Flat washer
9. 3/4 x 5--27/32” Clevis pin

10. 1/4 x 1--1/2” Cotter pin

11. 3/4 x 5--1/2” Bolt

12. 3/16 x 1--1/2” Cotter pin
13. 7/16 x 11/32” Klik pin
14. Category 2 hitch pin
15. 1--1/8 x 1--7/16 x 1--11/16” Sleeve
16. 1--1/8 x 2--3/8 x 3/16” Flat washer
17. 1--1/8 Slotted hex nut

DB2119

«
...
34
35
36
37
38
...
»

Summary of Contents for 208-2











































































Reviews:

No comments

Related manuals for 208-2

Brand: Rabe Pages: 65

Brand: DARAY Pages: 28

Brand: MacDon Pages: 88

Brand: Jiffy Pages: 15

Brand: Above All Pages: 4

Brand: Bard Pages: 36

Brand: Bard Pages: 2

Brand: Bard Pages: 30

Brand: Bard Peripheral Vascular Pages: 44

Brand: Hagie Pages: 141

SC 2 Deluxe EasyFix

Brand: Kärcher Pages: 12

Brand: Kärcher Pages: 16

Brand: Latham Pages: 4

Brand: SafeWaze Pages: 23

Brand: CAB Pages: 30

Aristo WeldCloud Mig U5000i

Brand: ESAB Pages: 28

UG 2200 Special

Brand: Amazone Pages: 252

Brand: HOFFEN Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands