background image

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

R

WOODBRIDGE 

www.woodbridgebath.com

1

R

WOODBRIDGE 

TOOLS REQUIRED FOR INSTALLATION

TOILET COMPONENTS

So

đ

 Cloth

or Blanket

Silicone

Silicone/

Caulk Gun

OTHER TOOLS MAY BE REQUIRED

Tape

Measure

Pencil/Marker

Safety Glass

Knife

During unpacking the product and prior to installation inspect your new product for any damages or
missing parts. Do not attempt to install or operate the product if the product is damaged.

Adjustable

Wrench

Channel

Lock Pliers

Adjustable

Socket Extension

Philips

Screwdriver

Level

Pu

ħ

y Knife

Bowl with lid

x 1

Toilet Seat Set

x 1

Wax Ring 

x 1

Moun

ng T-Bolt

x 2

bolt cap decora

on

x 2

Moun

ng Screw 

x 2

T-Bolt Nuts and Washers

x 2

The plas

c piece

x 2 

Plas

c washer

x 2

 

ELONGATED  TOILET 

READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT

2 PEOPLE ARE REQUIRED TO LIFT AND DURING

ENTIRE INSTALLATION OF THIS PRODUCT

INSTALLATION OF THIS PRODUCTS BY AN

INEXPERIENCED INSTALLER MAY RESULT

PERSONAL INJURY OR DEATH!

INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING

OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.

We reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior no

ce!

We

 shall not be liable for any injuries or property damages in connection with this product during installation or use of this product!

This products must be installed by a fully insured and licensed plumber only. Installation of any our product by anyone other
than fully insured and licensed plumber shall void limited warranty. We recommends that such licensed plumber have experience
in the installation of products.
Limited warranty is void on any commercial installation
We are not responsible for local code compliance for this product. Building and plumbing codes may vary from state-to-state in
accordance to your location. We are not resonsible for providing any compliance certifications.
Under no circumstances we are shall not be liable for any and all incidental damages sustained in connection with this product
Neither manufacture, nor distributor, nor retailer is responsible for water damage or flood caused due to use of this product.
Under no circumstances We shall not be liable for any and all fees, cost of installation/reinstallation/removal, subsequent
damage or transportation in case of the product defect

Summary of Contents for B0933











Reviews: