Wood-mizer LT40DC Series User Manual Download

Page: 23 / 135

Safety & General Information

Blade Sizes

Safety & General Information

30Sdoc120507

1-14

1.6

Blade Sizes

See Table 1-3.

Wood-Mizer TRU•SHARP™ offers three types of blades to provide effi-

cient sawing for all models of sawmills. The engine/motor size of your sawmill and the
type of wood you saw should determine which blade you choose for optimum perfor-
mance.

See

The Blade Handbook

for blade hook angle, tooth height, and tooth set specifica-

tions.

Softwood

Medium

Hardwood

Frozen Timber or
Dense Hardwood

5-15HP Gas

B275IH1030
B275IH741030

B375IH929

TRU•SHARP™ “F” blades use a 9/29 profile (9° hook angle and 29° back angle) and are designed

to cut frozen and/or extremely dense, hard-to-cut wood. Standard TRU•SHARP™ blades use a 10/30
profile.

7.4-11kW (10-15HP) Electric
16-25HP Gas
33HP Diesel

B376IH1030
B376IH741030

B275IH1030
B275IH741030
B376IH1030
B376IH741030

Customer may choose preferred blade.

B375IH929

15-18.5kW (20-25HP) Electric
42HP Diesel

B376IH1030
B376IH741030

B275IH1030
B275IH741030
B376IH1030
B376IH741030

B375IH929

TABLE 1-3

Summary of Contents for LT40DC Series








































































































































Search results

Summary of Contents for LT40DC Series

Reviews:

Related manuals for LT40DC Series

Brands by name

Popular brands

Wood-mizer LT40DC Series, User Manual

Search results

Summary of Contents for LT40DC Series

Reviews:

Related manuals for LT40DC Series

Brands by name

Popular brands