Wood master LT 90 Owner'S Manual Download Page 6

Page: 6 / 32

LT 90 Owners Manual

2015

Choosing Location

When installing your WoodMaster, keep in mind the direction of the winds during heating months. Try to place

the furnace in an area where exhaust will not be a problem for yourself or any surrounding neighbors.

LOCATION: It is recommended that the unit be located with due consideration to the prevailing wind direction.

• When using more that 4 feet of chimney extension external support is needed.

• Should be located greater than 100 feet from any residence not served.

• If located between 100 and 300 feet to any residence not served, it is recommended that the

stack be at least 100% of the height of the peak of the residence, plus an additional 2 feet.

Always remember to comply with all applicable state and local codes.

Chimney Specifications

To insure proper insulation, use only a Class A Insulated Chimney and Chimney Adapter from your local Wood

Master Dealer or Northwest Manufacturing, Inc. A draft inducer may be used to ensure proper draft under all

conditions.

Note: Remove the chimney cap prior to lighting the furnace.

CAUTION: Using a non-insulated chim

ney or failure to use a Class A Insulated Chimney WILL result in a voided Warranty. When using more than

four feet of chimney extension external support is needed.

Pad Supports

The LT 90 should be placed on cement

blocks. The blocks should be at least 6”

wide, 10” long and 3” thick. Two feet of

clearance from the front and rear of the fur

nace and at least one foot clearance on the

sides is recommended. Failure to install the

WoodMaster LT 90 on a proper support will

result in a voided warranty. Never use com

bustable materials, such as wood blocks,

to support the LT 90. A full cement pad is

recommended if the supporting ground is

soft, sandy, or othewise unable to support

the furnace on the pads alone.

Residence not

served by furnace

2 feet

Residence

served by furnace

Minimum of 100 feet

Chimney height

should be 2 feet above roof line

60.00

96.00

54.00

6.00

16.00

12.00

11.50

48.00

14.00

SUP

RET

Installation

Summary of Contents for LT 90

































Search results

Summary of Contents for LT 90

Reviews:

Related manuals for LT 90

Brands by name

Popular brands

Wood master LT 90, Owner'S Manual

Search results

Summary of Contents for LT 90

Reviews:

Related manuals for LT 90

Brands by name

Popular brands