background image

5

Dimensions in parentheses are in
millimeters unless otherwise specified.

I N S TA L L AT I O N

I N S T R U C T I O N S

10" 

(254)

OVERALL

HEIGHT

OVERALL WIDTH 

4" 

(102)

22" 

(559)

OVERALL DEPTH

12" 

(305) 

2" 

(51) 

3

/

4

(19)

DIAMETER

OF RAIL

OVERALL WIDTH 

4" 

(102)

24" 

(610)

OVERALL DEPTH

12" 

(305) 

18" 

(457)

OVERALL

HEIGHT

2" 

(51) 

3

/

4

(19)

DIAMETER

OF RAIL

OVERALL WIDTH 

27" 

(686)

OVERALL DEPTH

12" 

(305) 

18" 

(457)

OVERALL

HEIGHT

2" 

(51) 

4" 

(102)

3

/

4

(19)

DIAMETER

OF RAIL

OV E R A L L

D I M E N S I O N S

L O W - P R O F I L E   W A L L   H O O D S

Overall Widths

30" (762), 36" (914),

42" (1067) and 48" (1219)

Overall Height

10" (254)

Overall Depth (excluding rail)

22" (559)

Shipping Weight (shell only)

39–55 lbs

(18–25 kg)

Dimensions may vary to ±

1

/

8

" (3).

2 4 " ( 6 1 0 )   D E E P  W A L L   H O O D S

Overall Widths

30" (762), 36" (914),

42" (1067), 48" (1219), 54" (1372),

60" (1524) and 66" (1676)

Overall Height

18" (457)

Overall Depth (excluding rail)

24" (610)

Shipping Weight (shell only)

67–126 lbs

(30–57 kg)

Dimensions may vary to ±

1

/

8

" (3).

2 7 " ( 6 8 6 )   D E E P  W A L L   H O O D S

Overall Widths

30" (762), 36" (914),

42" (1067), 48" (1219), 54" (1372),

60" (1524) and 66" (1676)

Overall Height

18" (457)

Overall Depth (excluding rail)

27" (686)

Shipping Weight (shell only)

69–128 lbs

(31–58 kg)

Dimensions may vary to ±

1

/

8

" (3).

Low Profile Wall Hood

shown with (R) rail option

24" (610) Deep Wall Hood

shown with (R) rail option

27" (686) Deep Wall Hood

shown with (R) rail option

Summary of Contents for W302210I

























Reviews: