background image

Pro Wall Hood Specifications

9

wolfappliance.com/specs

Discharge Specifications

24" AND 27" DEEP WALL HOODS

The illustration below provides dimensions for vertical

discharge for 24" (610) and 27" (686) deep wall hoods.

These dimensions are critical for proper installation.

Dimension A in the illustration will vary with the width of

the hood. Refer to the chart below.

An optional horizontal discharge kit is available through

your authorized Wolf dealer. For local dealer information,

visit the find a showroom section of our website,

wolfappliance.com.

24" and 27" Deep Wall Hoods

WIDTH OF HOOD

A

30"

(762)

14

3

/

4

"

(375)

36"

(914)

17

3

/

4

"

(451)

42"

(1067)

*

20

3

/

4

"

(527)

48"

(1219)

*

23

3

/

4

"

(603)

54"

(1372)

*

26

3

/

4

"

(679)

60"

(1524)

*

29

3

/

4

"

(756)

66"

(1676)

*

32

3

/

4

"

(832)

Duct Cover

IMPORTANT NOTE:

If an optional duct cover is to be used

with any pro wall hood, it must be attached before

installing the hood. Installing a duct cover will impact all

aspects of the hood installation including hood location,

ducting, electrical placement and the mounting surface.

DUCT COVER INSTALLATION

Remove all screws from the front edge of the back

panel on the top of the wall hood. Leave the two

screws on the sides, there is a relief in the duct cover

for them.

Attach the duct cover from the inside of the hood

through the filter opening using the screws provided.

Leave screws partially loose until all screws are

installed. Check alignment of the duct cover with the

hood and tighten the four corner screws to secure the

duct cover. Tighten all remaining screws.

Proceed with installation of the wall hood.

DUCT COVER

MOUNTING

SCREWS

Duct cover installation.

9"

(229)

5

5

/

8

"

(143)

TO CENTER

OF TRANSITION

A

TO

CENTER OF

TRANSITION

24" and 27" deep wall hoods—vertical discharge.

Summary of Contents for Pro Wall

























Reviews: