FUNCTION
PROBLEM
CORRECTIVE ACTION
The coffee dispenses too
slowly.
Push the fineness of grind adjustment cu sor
2
to the right to make the ground coffee coarser
(according to the type of coffee used). Run one or
several rinsing cycles. Run a machine clean (see
section 12).
If it occurs during ground coffee recipe: choose a
coarser ground coffee powder or use a mixture for
espresso coffee machine
Your tea is not hot enough or
too hot.
Increase or reduce the hot water temperature in
the Settings menu.
After pre ground coffee funnel
3
closing, there is still ground
coffee inside.
Before inserting the second spoon, check if the
hatch is empty. If not, use the brush on the spoon
to unstick coffee. Be careful to close the hatch
after one spoon insertion, don’t put several spoons
in the hatch at the same time. Don’t tamp the
ground coffee in the hatch before closing it to
avoid stuck coffee.
Using
steam
The steam nozzle on your
machine seems to be partially
or completely blocked.
Dismantle the nozzle from its support using the
dismantling key (figu e F4). Replace the support
without the nozzle. Start the rinse cycle for the
One Touch Cappuccino block to remove any
remaining deposits. Clean the steam nozzle and
ensure that the opening of the nozzle is not
obstructed by the remains of milk or limescale. Use
the cleaning needle if necessary (figu e F5).
No steam comes out of the
steam nozzle.
Ensure that the steam nozzle is not blocked. See
The steam nozzle on your machine seems to be
partially or completely blocked above. If this does
not work, empty the water tank and remove the
Claris filter tempo arily. Fill the water tank with
mineral water with high calcium content (>100
mg/l) and run steam cycles (5 to 10) consecutively
into a container until you obtain a continuous jet
of steam. Put the filter back in the tank and come
back to use regular water.
Steam is leaking from the drip
tray grid.
Depending on the type of preparation, steam may
escape from the drip tray grid.
Using
maintenance
The drip tray has been
emptied, but the warning
message is still displayed on
the screen.
The metal contacts are dirty. Clean and wipe the
metal contacts at the back of the drip tray.
The machine does not request
descaling.
The descaling cycle is requested after a large
number of recipes.
There is few flowing th ough
coffee nozzle during descaling.
During descaling, several actions are in progress in
the appliance, without permanent flowing th ough
nozzle.
51
SV
RU
RO
PL
NO
NL
FI
DA
CS
IT
ES
FR
EN
DE
Summary of Contents for PERFECTION 800L Series
