WMF 1300 S User Manual Download

Page: 46 / 136

User Manual WMF 1300 S

Software | Overview

5 Software

• When setting beverages, the same safety

instructions apply as for operating the coffee
machine.

> Follow all operation safety instructions.

5.1 Overview

Ready to operate

page 48

Espresso

Cappuccino

Café Crème

Latte Macchiato

Ristretto

Milk coffee

1300S

DI_02_01_00_00

Button layout

Operating options

page 63
The pads and buttons available on
the display depend on the settings
and the machine model.

“Ready to operate” display pads

Eco mode (active)

Warm rinsing

SteamJet cup warmer

Barista (coffee strength)

S-M-L pad

Cup size adjustment

Milk system refill

Second type of coffee
(decaf)

page 49

CAUTION

Operation safety instructions

page 30

Summary of Contents for 1300 S









































































































































Search results

Summary of Contents for 1300 S

Reviews:

Related manuals for 1300 S

Brands by name

Popular brands

WMF 1300 S, User Manual

Search results

Summary of Contents for 1300 S

Reviews:

Related manuals for 1300 S

Brands by name

Popular brands